WP3363394 Whirlpool Washer Drain Pump
Part #: WPL WP3363394
This Top Load Washer Drain Pump removes water from your top-load washer during the drain portion of the wash cycle. This pump mounts directly to the washing machine’s motor with two clips (item WP8546127). If your washer doesn’t drain properly, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation. Recommended Item: The Repair Manual (item 4313896) for your washer is a useful reference when replacing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drain Pump
• Tools Needed: Multi screwdriver, standard pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drain Pump
• Tools Needed: Multi screwdriver, standard pliers
Weight : 27.625900 lbs
Dimension : 19.690000 x 11.570000 x 16.130000
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
This Top Load Washer Drain Pump removes water from your top-load washer during the drain portion of the wash cycle. This pump mounts directly to the washing machine’s motor with two clips (item WP8546127). If your washer doesn’t drain properly, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation. Recommended Item: The Repair Manual (item 4313896) for your washer is a useful reference when replacing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drain Pump
• Tools Needed: Multi screwdriver, standard pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drain Pump
• Tools Needed: Multi screwdriver, standard pliers
Weight : 27.625900 lbs
Dimension : 19.690000 x 11.570000 x 16.130000
Write Your Own Review
The following parts are replaced by this product
- 3363394
- 3348015
- 3352492
- 62516
- 63347
- 64076
- 3363394BULK
DIY Guide to Replacing the WP3363394 Whirlpool Drain Pump
Introduction
Replacing the Whirlpool WP3363394 drain pump in your washing machine can be a straightforward task with the right instructions. This DIY guide will walk you through the steps to do so safely and efficiently.
Step 1: Unplug Your Washer
For safety purposes, unplug your washer before beginning any repairs.
Step 2: Remove the Top-Panel
Remove the two screws that are securing the top-panel on your washer. Once loosened, carefully lift off the panel and place it aside.
Step 3: Disconnect the Hoses
Disconnect the hoses connected to the drain pump by squeezing the clamps and pulling them off. Then disconnect the wires from the terminals.
Step 4: Remove the Old Pump
Using a Phillips-head screwdriver, unscrew the four screws around the pump. You can then carefully lift the old pump out and discard it.
Step 5: Install the New Pump
Take the new Whirlpool WP3363394 drain pump and place it into the same position as the old one. Secure it using the screws. Then attach the hoses and plug in the wires.
Step 6: Reassemble Your Washer
Once the new pump is installed, reconnect the hoses and wires securely. Reattach the top-panel and two screws.
Step 7: Test the New Pump
Plug your washer back in and test the new pump to ensure it is functioning properly. If there are any issues, please refer to professional help.
Conclusion
Replacing the Whirlpool WP3363394 drain pump in your washing machine is an easy task with these helpful instructions. Now your machine should be as good as new!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Introduction
Replacing the Whirlpool WP3363394 drain pump in your washing machine can be a straightforward task with the right instructions. This DIY guide will walk you through the steps to do so safely and efficiently.
Step 1: Unplug Your Washer
For safety purposes, unplug your washer before beginning any repairs.
Step 2: Remove the Top-Panel
Remove the two screws that are securing the top-panel on your washer. Once loosened, carefully lift off the panel and place it aside.
Step 3: Disconnect the Hoses
Disconnect the hoses connected to the drain pump by squeezing the clamps and pulling them off. Then disconnect the wires from the terminals.
Step 4: Remove the Old Pump
Using a Phillips-head screwdriver, unscrew the four screws around the pump. You can then carefully lift the old pump out and discard it.
Step 5: Install the New Pump
Take the new Whirlpool WP3363394 drain pump and place it into the same position as the old one. Secure it using the screws. Then attach the hoses and plug in the wires.
Step 6: Reassemble Your Washer
Once the new pump is installed, reconnect the hoses and wires securely. Reattach the top-panel and two screws.
Step 7: Test the New Pump
Plug your washer back in and test the new pump to ensure it is functioning properly. If there are any issues, please refer to professional help.
Conclusion
Replacing the Whirlpool WP3363394 drain pump in your washing machine is an easy task with these helpful instructions. Now your machine should be as good as new!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.