280114 Whirlpool Dryer Drum Seal
This Dryer Drum Felt Seal is what seals the hot air into the dryer drum as it rotates. If hot air is leaking out of your dryer, the seal is likely damaged and needs to be replaced. This seal is compatible with many different models and may fit both the front and rear. Includes 1 seal and adhesive to install. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Felt Seal
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Felt Seal
• Tools Needed: Multi screwdriver
Weight : 1.8987 lbs
Dimension : 8.937 x 8.622 x 3.4251
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
This Dryer Drum Felt Seal is what seals the hot air into the dryer drum as it rotates. If hot air is leaking out of your dryer, the seal is likely damaged and needs to be replaced. This seal is compatible with many different models and may fit both the front and rear. Includes 1 seal and adhesive to install. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Felt Seal
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Felt Seal
• Tools Needed: Multi screwdriver
Weight : 1.8987 lbs
Dimension : 8.937 x 8.622 x 3.4251
Write Your Own Review
The following parts are replaced by this product
- 697694
- 3403265
1. Unplug the Whirlpool dryer from the wall outlet and move it to an area with ample space.
2. Remove the lint filter cover and then remove the lint filter.
3. Remove the four screws that hold the top panel in place and lift off the top panel gently.
4. Disconnect the wiring harnesses from both ends of the drum and then pull out the drum.
5. Remove the parts that make up the existing drum seal, such as the felt, adhesive and clips.
6. Clean up any dirt or debris from the edges of the frame and the area where the drum seal will be installed.
7. Place the new drum seal into place and secure it with adhesive and clips.
8. Reinstall the drum and reconnect the wiring harnesses.
9. Replace the lint filter and lint filter cover.
10. Put the top panel back in place and secure it with its fastening screws.
11. Plug the Whirlpool dryer back into its original wall outlet.
12. Run a few test cycles to ensure that the drum seal is properly installed.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
2. Remove the lint filter cover and then remove the lint filter.
3. Remove the four screws that hold the top panel in place and lift off the top panel gently.
4. Disconnect the wiring harnesses from both ends of the drum and then pull out the drum.
5. Remove the parts that make up the existing drum seal, such as the felt, adhesive and clips.
6. Clean up any dirt or debris from the edges of the frame and the area where the drum seal will be installed.
7. Place the new drum seal into place and secure it with adhesive and clips.
8. Reinstall the drum and reconnect the wiring harnesses.
9. Replace the lint filter and lint filter cover.
10. Put the top panel back in place and secure it with its fastening screws.
11. Plug the Whirlpool dryer back into its original wall outlet.
12. Run a few test cycles to ensure that the drum seal is properly installed.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
