WPW10119326 Whirlpool Speed Control
The Stand Mixer Speed Control Plate controls the speed of the stand mixer motor. The speed control plate is part of the speed control system. If the contacts aren't closing and your mixer is running loud, or if the contacts have failed and your mixer is no longer turning on, replacing the control plate may alleviate these issues. To access the part, remove all attachments and the bowl of the mixer. Then remove the back cover of the mixer and the screws from the trim band. Remove the wires from the seal of the mixer in order to take the spring off of the speed control plate. Make sure you hook the spring with a needle nose pliers securely to remove. Disconnect the wires from the phase control board. You'll then be able to remove the upper two screws holding in the old speed control plate. Note: These upper two screws are where you adjust the speed of your mixer. Make sure you measure them from the back of their post to the back of the speed control plate at 3/8-in. Replacing this part will require basic hand tools, some disassembly of the stand mixer and novice repair experience. You must unplug the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Stand Mixer Speed Control Plate Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Stand Mixer Speed Control Plate Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Weight : 0.064700 lbs
Dimension : 3.120000 x 2.500000 x 1.000000
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
The Stand Mixer Speed Control Plate controls the speed of the stand mixer motor. The speed control plate is part of the speed control system. If the contacts aren't closing and your mixer is running loud, or if the contacts have failed and your mixer is no longer turning on, replacing the control plate may alleviate these issues. To access the part, remove all attachments and the bowl of the mixer. Then remove the back cover of the mixer and the screws from the trim band. Remove the wires from the seal of the mixer in order to take the spring off of the speed control plate. Make sure you hook the spring with a needle nose pliers securely to remove. Disconnect the wires from the phase control board. You'll then be able to remove the upper two screws holding in the old speed control plate. Note: These upper two screws are where you adjust the speed of your mixer. Make sure you measure them from the back of their post to the back of the speed control plate at 3/8-in. Replacing this part will require basic hand tools, some disassembly of the stand mixer and novice repair experience. You must unplug the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Stand Mixer Speed Control Plate Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Stand Mixer Speed Control Plate Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Weight : 0.064700 lbs
Dimension : 3.120000 x 2.500000 x 1.000000
Write Your Own Review
The following parts are replaced by this product
- 4162402
- W10119326
Replacing the WPW10119326 Whirlpool Speed Control Plate
1. Unplug your dryer from the wall before beginning any maintenance work.
2. Remove the front panel of the dryer by unscrewing the corner screws and pulling the front panel away from the dryer body.
3. Disconnect the wiring harness from the speed control plate by squeezing the locking tabs and then pulling the wires apart.
4. Unscrew the mounting screws from the speed control plate and remove the plate from the dryer.
5. Place the new speed control plate in place, making sure to line up the mounting holes, and secure with the screws.
6. Reconnect the wiring harness to the speed control plate.
7. Replace the front panel of the dryer and secure with the screws.
8. Plug your dryer back into the wall and test the operation.
Tips:
- Use a Phillips head screwdriver for all screws
- Wipe down the area after removing the old speed control plate to avoid installing debris in the dryer
- Wear protective gloves while replacing speed control plate
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Unplug your dryer from the wall before beginning any maintenance work.
2. Remove the front panel of the dryer by unscrewing the corner screws and pulling the front panel away from the dryer body.
3. Disconnect the wiring harness from the speed control plate by squeezing the locking tabs and then pulling the wires apart.
4. Unscrew the mounting screws from the speed control plate and remove the plate from the dryer.
5. Place the new speed control plate in place, making sure to line up the mounting holes, and secure with the screws.
6. Reconnect the wiring harness to the speed control plate.
7. Replace the front panel of the dryer and secure with the screws.
8. Plug your dryer back into the wall and test the operation.
Tips:
- Use a Phillips head screwdriver for all screws
- Wipe down the area after removing the old speed control plate to avoid installing debris in the dryer
- Wear protective gloves while replacing speed control plate
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
