WP8544771 Whirlpool Dryer Heating Element
The Dryer Heating Element Assembly generates heat in the appliance during the drying cycle. If your dryer isn’t heating properly, check for a blown thermal fuse or thermal cut out. If you see a break in the coil of your appliance’s heating element, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Heating Element Assembly
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Heating Element Assembly
• Tools Needed: Multi screwdriver
Weight : 2.266200 lbs
Dimension : 14.500000 x 6.750000 x 2.500000
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
The Dryer Heating Element Assembly generates heat in the appliance during the drying cycle. If your dryer isn’t heating properly, check for a blown thermal fuse or thermal cut out. If you see a break in the coil of your appliance’s heating element, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Heating Element Assembly
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Heating Element Assembly
• Tools Needed: Multi screwdriver
Weight : 2.266200 lbs
Dimension : 14.500000 x 6.750000 x 2.500000
Write Your Own Review
The following parts are replaced by this product
- 8544771
- DE4771
- 8544771
Step 1: Unplug Washer From Power Source
Unplug the washer from the power source by pulling the electrical plug to the wall outlet.
Step 2: Disconnect Water Lines
Disconnect the water lines which feed into the back of the washer using an adjustable wrench.
Step 3: Remove Access Panel
Remove the access panel located in the rear of the washer, which is usually secured with several screws.
Step 4: Disconnect Heating Element
Unscrew the heating element assembly from the rear panel, then pull it out and disconnect the wires.
Step 5: Install WP8544771 Heating Element
Replace the old heating element with a new WP8544771 heating element. Make sure to secure the wires and screws properly before you set it back into the panel.
Step 6: Reinstall Access Panel
Place the access panel back into position and secure the screws tightly.
Step 7: Reconnect Water Lines
Turn the water supply back on, then reconnect the water lines to the washer.
Step 8: Plug Washer Back In
Plug the washer back into the power source, then turn it on to make sure the new heating element is working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Unplug the washer from the power source by pulling the electrical plug to the wall outlet.
Step 2: Disconnect Water Lines
Disconnect the water lines which feed into the back of the washer using an adjustable wrench.
Step 3: Remove Access Panel
Remove the access panel located in the rear of the washer, which is usually secured with several screws.
Step 4: Disconnect Heating Element
Unscrew the heating element assembly from the rear panel, then pull it out and disconnect the wires.
Step 5: Install WP8544771 Heating Element
Replace the old heating element with a new WP8544771 heating element. Make sure to secure the wires and screws properly before you set it back into the panel.
Step 6: Reinstall Access Panel
Place the access panel back into position and secure the screws tightly.
Step 7: Reconnect Water Lines
Turn the water supply back on, then reconnect the water lines to the washer.
Step 8: Plug Washer Back In
Plug the washer back into the power source, then turn it on to make sure the new heating element is working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
