WE12X10014 GE Washer Drive Belt
GE - Hotpoint - RCA Dryer Drum Belt WE12X10014
● 4 Ridges
● 87" long
● Manufacturer part number on belt can be 123C7487P003
● Replaces WE12X42, WE12X10001, WE12X10009 and WE12X82
Same as Frigidaire 131553800
We are a Factory Authorized Parts Distributor for General Electric. Trust us for all of your General Electric appliance parts and accessories needs.
● 4 Ridges
● 87" long
● Manufacturer part number on belt can be 123C7487P003
● Replaces WE12X42, WE12X10001, WE12X10009 and WE12X82
Same as Frigidaire 131553800
We are a Factory Authorized Parts Distributor for General Electric. Trust us for all of your General Electric appliance parts and accessories needs.
Weight : 0.3013 lbs
Dimension : 7.0866 x 3.6614 x 1.6141
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
GE - Hotpoint - RCA Dryer Drum Belt WE12X10014
● 4 Ridges
● 87" long
● Manufacturer part number on belt can be 123C7487P003
● Replaces WE12X42, WE12X10001, WE12X10009 and WE12X82
Same as Frigidaire 131553800
We are a Factory Authorized Parts Distributor for General Electric. Trust us for all of your General Electric appliance parts and accessories needs.
● 4 Ridges
● 87" long
● Manufacturer part number on belt can be 123C7487P003
● Replaces WE12X42, WE12X10001, WE12X10009 and WE12X82
Same as Frigidaire 131553800
We are a Factory Authorized Parts Distributor for General Electric. Trust us for all of your General Electric appliance parts and accessories needs.
Weight : 0.3013 lbs
Dimension : 7.0866 x 3.6614 x 1.6141
Write Your Own Review
The following parts are replaced by this product
- WE12X82
- LB216
- WE12X42
- WE12X42P
- WE12X82P
- WE12X0042
- WE12X0082
1. Unplug the dryer's power cord from the wall outlet.
2. Remove the two Phillips screws on the dryer's back panel.
3. Pull the dryer away from the wall, allowing access to the rear of it.
4. Locate the drive belt and tension pulley wheel on the back of the dryer.
5. Release the tension on the pulley wheel by loosening the bolt in the center of it.
6. Pull the belt off the motor pulley and the pulley wheel.
7. Feed the new belt around the drum, then through the idler pulley wheel and the motor pulley.
8. Pull the belt tight and secure it.
9. Re-tighten the tension pulley bolt, then push the dryer back into its original position.
10. Replace the back panel screws and plug the power cord into the wall outlet.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
2. Remove the two Phillips screws on the dryer's back panel.
3. Pull the dryer away from the wall, allowing access to the rear of it.
4. Locate the drive belt and tension pulley wheel on the back of the dryer.
5. Release the tension on the pulley wheel by loosening the bolt in the center of it.
6. Pull the belt off the motor pulley and the pulley wheel.
7. Feed the new belt around the drum, then through the idler pulley wheel and the motor pulley.
8. Pull the belt tight and secure it.
9. Re-tighten the tension pulley bolt, then push the dryer back into its original position.
10. Replace the back panel screws and plug the power cord into the wall outlet.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
