WP8318268 Whirlpool Thermostat
This Dryer Cycling Thermostat monitors and regulates the temperature inside the dryer. If the cycling thermostat is no longer working properly, you may notice that your dryer will not heat. Note that a multimeter (item 964740) can be used to test for continuity to determine if the thermostat is defective and requires replacement. This assembly includes (1) adjustable dryer cycling thermostat with an internal-bias heater (WP3387134) and installation instructions. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. The location of the cycling thermostat varies from model to model; refer to the installation instructions for additional information.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Cycling Thermostat
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Cycling Thermostat
• Tools Needed: Multi screwdriver
Weight : 0.0734 lbs
Dimension : 3.1496 x 2.0078 x 1.6141
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
This Dryer Cycling Thermostat monitors and regulates the temperature inside the dryer. If the cycling thermostat is no longer working properly, you may notice that your dryer will not heat. Note that a multimeter (item 964740) can be used to test for continuity to determine if the thermostat is defective and requires replacement. This assembly includes (1) adjustable dryer cycling thermostat with an internal-bias heater (WP3387134) and installation instructions. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. The location of the cycling thermostat varies from model to model; refer to the installation instructions for additional information.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Cycling Thermostat
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Cycling Thermostat
• Tools Needed: Multi screwdriver
Weight : 0.0734 lbs
Dimension : 3.1496 x 2.0078 x 1.6141
Write Your Own Review
The following parts are replaced by this product
- 3977706
- 3977425
- 8318268
How to Replace the Whirlpool WP8318268 THRMST-FIX
1. Unplug the appliance and shut off the gas or power source, depending on your stove type.
2. Remove the oven door and detach the insulation in order to access the rear panel where the THRMST-FIX is located.
3. Disconnect the wires from the THRMST-FIX. Be sure to note the position of the wires and how they were connected before disconnecting them.
4. Carefully remove the THRMST-FIX from its mounting bracket, taking note of how it was mounted.
5. Install the new THRMST-FIX in the same manner as the old one.
6. Reconnect the wires to their original positions.
7. Secure the new THRMST-FIX to the mounting bracket.
8. Reinstall the insulation and oven door.
9. Plug the appliance back in and restore the gas or power source.
10. Test the new THRMST-FIX to ensure it is working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Unplug the appliance and shut off the gas or power source, depending on your stove type.
2. Remove the oven door and detach the insulation in order to access the rear panel where the THRMST-FIX is located.
3. Disconnect the wires from the THRMST-FIX. Be sure to note the position of the wires and how they were connected before disconnecting them.
4. Carefully remove the THRMST-FIX from its mounting bracket, taking note of how it was mounted.
5. Install the new THRMST-FIX in the same manner as the old one.
6. Reconnect the wires to their original positions.
7. Secure the new THRMST-FIX to the mounting bracket.
8. Reinstall the insulation and oven door.
9. Plug the appliance back in and restore the gas or power source.
10. Test the new THRMST-FIX to ensure it is working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
