W10337248 Whirlpool Microwave Motor Coupler Support
This Microwave Glass Turntable Coupling is a replacement part for your current microwave coupling. To replace, remove the glass turntable from the microwave and pull out the old coupling. Install the new motor coupling by aligning it on the turntable motor shaft as you insert it into the base. Then replace the turntable. This accessory easily replaces a damaged coupling and is compatible with several microwave brands. Check to see if your model number is compatible. Installing this accessory will not require tools, disassembly of the microwave or repair experience.
Part Specification
• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• Package contains (1) Microwave Glass Turntable Drive Coupling
• No tools required for installation
Part Specification
• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• Package contains (1) Microwave Glass Turntable Drive Coupling
• No tools required for installation
Weight : 0.028800 lbs
Dimension : 1.500000 x 1.500000 x 0.750000
This Microwave Glass Turntable Coupling is a replacement part for your current microwave coupling. To replace, remove the glass turntable from the microwave and pull out the old coupling. Install the new motor coupling by aligning it on the turntable motor shaft as you insert it into the base. Then replace the turntable. This accessory easily replaces a damaged coupling and is compatible with several microwave brands. Check to see if your model number is compatible. Installing this accessory will not require tools, disassembly of the microwave or repair experience.
Part Specification
• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• Package contains (1) Microwave Glass Turntable Drive Coupling
• No tools required for installation
Part Specification
• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• Package contains (1) Microwave Glass Turntable Drive Coupling
• No tools required for installation
Weight : 0.028800 lbs
Dimension : 1.500000 x 1.500000 x 0.750000
Write Your Own Review
Replacing the W10337248 Whirlpool Microwave Motor Coupler Support
1. Unplug the power cord of the microwave from the wall outlet before beginning the replacement process.
2. Open the rear access panel of the microwave using a Phillips head screwdriver.
3. Locate the motor coupler support on the right side of the unit.
4. Remove the screws that hold the motor coupler support in place, using a Phillips head screwdriver.
5. Carefully remove the old motor coupler support from the unit and discard it.
6. Take the new motor coupler support and insert it into the cavity where the old one was located.
7. Securely tighten the screws to keep the new motor coupler support in place.
8. Test out the new motor coupler support by plugging the power cord back into the wall outlet and running the microwave for a few minutes.
9. If everything works properly, the replacement process is complete.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Unplug the power cord of the microwave from the wall outlet before beginning the replacement process.
2. Open the rear access panel of the microwave using a Phillips head screwdriver.
3. Locate the motor coupler support on the right side of the unit.
4. Remove the screws that hold the motor coupler support in place, using a Phillips head screwdriver.
5. Carefully remove the old motor coupler support from the unit and discard it.
6. Take the new motor coupler support and insert it into the cavity where the old one was located.
7. Securely tighten the screws to keep the new motor coupler support in place.
8. Test out the new motor coupler support by plugging the power cord back into the wall outlet and running the microwave for a few minutes.
9. If everything works properly, the replacement process is complete.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
