Maytag Appliance Parts Washer Dryer Combo Parts

The Top Load Washer Lid Switch Assembly detects if the lid of the washer is open or closed and prevents the appliance from spinning or agitating if the lid isn’t secured. If ... your washer won’t initiate the cleaning cycle, the current lid switch could be damaged and require replacement. This assembly includes (1) lid switch with actuator and wire harness, (2) zip ties and installation instructions. Installing this part will require basic hand tools, disassembly of the washing machine and novice repair experience. You must unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Lid Switch Assembly• Tools Needed: Multi screwdriver Read More Read Less

This Top Load Washer Tub Bearing Kit is installed between the two tubs, and seals the water into the tubs. This kit includes the hub assembly, seal and spanner nut. If the bea ...ring in your appliance is causing it to no longer function properly, replacing this part may alliviate the issue. If your washer isn't spinning as expected during operation, replacing this part may alleviate the issue. Note that the mounting stem and tub bearing kits are sold separately, but should be replaced at the same time. We strongly recommend that you hire a qualified technician to safely install this part. Replacing this part will require advanced mechanical training. Specialized tools, complex testing and appliance calibration may be required. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Tub Bearing Kit• Tools Needed: Specialized Tools Read More Read Less

The Dryer Terminal Block is located on the back of your electric dryer where the power cord attaches to the appliance. This assembly includes the terminal block and installati ...on instructions; hardware is not included, you will need to use existing hardware. If your dryer is no longer receiving power, the terminal block may need to be replaced. Installing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Terminal Block• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

The Dryer Lint Filter Grille is a white plastic part that fits inside the lint screen housing and keeps clothing from slipping into the lint duct. If the existing part is crac ...ked or damaged and your clothes are getting caught on the Grille during the drying cycle, replacing this part may alleviate these issues. Replacing the Grille will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Lint Filter Grille• Tools Needed: Multi screwdriver Read More Read Less

Maintain the functionality of your washer with this durable handle, designed specifically for a range of compatible brands including Admiral, Amana, Jenn-Air, Kenmore, Kitchen ...aid, Magic Chef, Maytag, Norge, Roper, and Whirlpool. Constructed with high-quality materials, it ensures longevity and reliable performance. The ergonomic design provides a comfortable grip, making it easy to open and close your appliance. Whether you’re replacing a worn-out handle or performing routine maintenance, this part is engineered to meet or exceed original equipment specifications. Keep your washer operating smoothly and maintain the convenience of your laundry routine. Elevate your appliance's performance with this essential replacement handle today. Read More Read Less

This Top Load Washer Start Capacitor briefly increases the voltage to the motor to help the motor start. If your washer motor won't start or hums, this part may need to be rep ...laced. Remove the washer console and then the spring clips that hold the body to the frame of the washer. Transfer the old foam shield holding the old capacitor to the new part before installing. Specifications: 189-227MFD, 125VAC, 60HZ. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Start Capacitor• Tools Needed: Multi screwdriver, putty knife Read More Read Less

This Dryer Blower Wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. If your dryer is making noise ...during use or not drying your clothes as expected, replacing this part may alleviate these issues. This part is housed on the bottom, inside of the appliance and attaches to the drive motor shaft. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Blower Wheel• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Idler Pulley Arm attaches to the idler pulley wheel and the idler pulley wheel helps the drive belt rotate the dryer drum. The main reason you might need to replace ...this part is if the bearing is damaged. To access this part, you'll need to remove your dryer door and the front panel of your dryer. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Recommended Items: Drive Belt (item 661570V). The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. If the drum will not turn when the dryer is turned on the belt is likely broken. While the dryer is disassembled, also consider replacing the idler pulley (item W10116792).Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Idler Pulley Arm• Tools Needed: Multi screwdriver Read More Read Less

The Gas Dryer Igniter lights the gas in your dryer. If your dryer is no longer supplying heat, this part may be damaged or cracked and may need to be replaced. To access the p ...art, lift the top of the dryer by releasing the spring clips from the top panel with a putty knife. Then remove the door switch wires and the screws that release the front panel. Next, simply loosen the screw that holds in the igniter to remove it. Please note that the bracket is no longer included with this part. If your original igniter was round, also order bracket (item 37001309). Replacing this assembly will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Note that you cannot touch the grey part of the igniter; only handle the igniter by its white plastic covering.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Igniter Kit• Tools Needed: Multi screwdriver, putty knife, 5/16" wrench Read More Read Less

This Washer Drain Hose carries used water from the washer to your house drain. To access the part, remove the back panel of your washer, then the lower front access panel. Whe ...n disconnecting any hoses, place a towel down to catch any water. You'll need to transfer over the old clamps to the new hose. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Washer Drain Hose• Tools Needed: Multi screwdriver, standard pliers, torque 20 screwdriver Read More Read Less