WPW10136934 Whirlpool Belt
The Dryer Drum Belt circles the dryer’s drum and attaches it to the motor to create constant motion during the drying cycle. If your dryer’s motor is running but the drum isn't turning, replacing this part may alleviate the issue. To access the part, first lift up the lint screen cover and remove the two screws. If you have the type of lint screen that has the cover built in, just pull it out and then remove the screws. Next, take a putty knife around the edge of the top of your dryer and find the release clips--press these in to release the top of the dryer so you can swing it open. The front panel also needs to be removed to replace the belt. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Belt
• Tools Needed: Multi screwdriver, putty knife
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Belt
• Tools Needed: Multi screwdriver, putty knife
Weight : 0.7605 lbs
Dimension : 10 x 6.1023 x 1.7322
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
The Dryer Drum Belt circles the dryer’s drum and attaches it to the motor to create constant motion during the drying cycle. If your dryer’s motor is running but the drum isn't turning, replacing this part may alleviate the issue. To access the part, first lift up the lint screen cover and remove the two screws. If you have the type of lint screen that has the cover built in, just pull it out and then remove the screws. Next, take a putty knife around the edge of the top of your dryer and find the release clips--press these in to release the top of the dryer so you can swing it open. The front panel also needs to be removed to replace the belt. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Belt
• Tools Needed: Multi screwdriver, putty knife
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Drum Belt
• Tools Needed: Multi screwdriver, putty knife
Weight : 0.7605 lbs
Dimension : 10 x 6.1023 x 1.7322
Write Your Own Review
The following parts are replaced by this product
- W10136934
DIY Guide to Replacing the Whirlpool WPW10136934 BELT
1. Before you start, make sure that you unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator. Wear protective eyewear and gloves while working on the refrigerator.
2. Open the door of the refrigerator and locate the belt in the motor compartment on the back of the refrigerator. Disconnect the power supply to the motor.
3. Remove the mounting screws on the motor and slide the motor out of the mounting bracket.
4. Remove the worn belt from the pulleys and discard it.
5. Place the new belt over the pulleys, making sure that it is tensioned evenly.
6. Carefully re-install the motor and mounting screws. Reconnect the power supply to the motor.
7. Close the door of the refrigerator and plug it back into the wall outlet. Turn on the water supply to the refrigerator.
8. Test the refrigerator to make sure the belt is working properly. Make any adjustments to the tension if needed.
By following these simple steps, your Whirlpool WPW10136934 BELT should be replaced quickly and easily.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Before you start, make sure that you unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator. Wear protective eyewear and gloves while working on the refrigerator.
2. Open the door of the refrigerator and locate the belt in the motor compartment on the back of the refrigerator. Disconnect the power supply to the motor.
3. Remove the mounting screws on the motor and slide the motor out of the mounting bracket.
4. Remove the worn belt from the pulleys and discard it.
5. Place the new belt over the pulleys, making sure that it is tensioned evenly.
6. Carefully re-install the motor and mounting screws. Reconnect the power supply to the motor.
7. Close the door of the refrigerator and plug it back into the wall outlet. Turn on the water supply to the refrigerator.
8. Test the refrigerator to make sure the belt is working properly. Make any adjustments to the tension if needed.
By following these simple steps, your Whirlpool WPW10136934 BELT should be replaced quickly and easily.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
