Whirlpool Washer Parts

The Washer Tub Ring snaps over the top of the tub and creates a splash shield. If your washer's tub ring is cracked or damaged, your washer may become unbalanced and shake, an ...d you may need to replace this part. A damaged wing may also cause the washer to jam by allowing clothing to get between the two tubs. To access the tub ring, tape the washer lid down and remove the top two hinge screws at the back of the appliance that secure the top hinges to the rear panel. Remove the screws to the wiring and hinge cover and remove the cover. Then pull the main top forward and up to access the inside tub. Installing this part will require basic hand tools, minor disassembly of the washing machine and novice repair experience. You must unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off your washer's hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Washer Tub Ring• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Thermal Cut Off Fuse is a safety device designed to protect the dryer from overheating. A multimeter can be used to test the fuse. Always check the dryer venting wh ...en replacing a blown thermal fuse. The thermal cut off is located on top of the burner funnel under the dryer drum, so you'll need to remove the drum from the dryer cabinet to access the old part and replace it. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Thermal Cut Off Fuse• Tools Needed: Multi screwdriver, putty knife, 5/16" nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Washer Water Inlet Valve Assembly helps to control and balance the water temperature flowing into the washer tub by controlling the water flow into the washer. This assem ...bly includes the cold water inlet valve, hot water inlet valve, wire harness and housing. If your washer isn't filling with water as expected, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Washer Water Inlet Valve Assembly• Tools Needed: Multi screwdriver, 10" V-Jaw Tongue & Groove Pliers, tape, putty knife, standard pliers, nylon lanyard Read More Read Less

This Front Load Washer Water Inlet Valve lets the hot and cold water into your washing machine and distributes it around to the dispensers. If the valve is leaking or your app ...liance isn't filling with water as expected, replacing this part may alleviate these issues. Please note: The valve should never be disassembled and cleaned, only replaced. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Washer Water Inlet Valve• Tools Needed: Multi screwdriver, standard pliers, torque 20 wrench, 10" V-Jaw tongue & groove pliers Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Top Load Washer Water Inlet Valve allows hot water to fill in the washer during the cleaning cycle. If your washer isn’t getting any hot water, filling slowly, not fill ...ing at all, or leaking hot water onto the floor, replacing this part may alleviate these issues. This part attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. Recommended Item: Consider replacing the Fill Hose (item 8212487RP) at the same time as this repair. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Water Inlet Valve• Tools Needed: Multi screwdriver Read More Read Less

This Top Load Washer Lid Latch Assembly tells your washer the lid is closed so it can go into its spin cycle, and also locks the lid. The full kit includes an instruction manu ...al, two different colored bezels depending on the color of your washer, and the lid latch assembly. If your washer isn't starting as expected, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Lid Latch Assembly Kit• Tools Needed: Multi screwdriver, standard pliers, 1/4" nut driver Read More Read Less

This Front Load Washer Shock Absorber absorbs the vibrations and movements of the outer washer tub. Your washer has 4 shock absorbers – 2 in the back and 2 in the front. If ...your tub is shaking while in cycle, replacing this part may alleviate the issue. You'll remove the hose and the back panel behind the machine to access this part. Turn the old shock absorber 90 degrees on the top and bottom to release it from the appliance. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Washer Shock Absorber• Tools Needed: Multi screwdriver, channel locks, pliers Read More Read Less

This Dryer Lint Filter is a gray screen that provides proper air flow and operation of your dryer. If your dryer's lint filter is damaged or missing, replacing this part may a ...lleviate these issues. The filter should be cleaned before every load of laundry and replaced immediately if damaged. Replacing your dryer’s lint filter is a quick and essential way to keep your appliance operating at optimal levels. Replacing this part will require no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Lint Filter• No tools required for installation Read More Read Less