WH01X26970 GE Suspension Rod Support
The GE WH01X26970 Ball Joint Upper is a durable, high-quality part designed to keep your GE washer functioning optimally. This upper ball joint attaches the outer tub to the inner frame, allowing for less vibration and better performance. It comes with a 1 year limited warranty and is designed to fit select GE washers. The GE WH01X26970 Ball Joint Upper is easy to install and is a great value for money. Get it today and keep your washer running smoothly. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!
Weight : 0.6043 lbs
Dimension : 8 x 7.5 x 1.4
The GE WH01X26970 Ball Joint Upper is a durable, high-quality part designed to keep your GE washer functioning optimally. This upper ball joint attaches the outer tub to the inner frame, allowing for less vibration and better performance. It comes with a 1 year limited warranty and is designed to fit select GE washers. The GE WH01X26970 Ball Joint Upper is easy to install and is a great value for money. Get it today and keep your washer running smoothly. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!
Weight : 0.6043 lbs
Dimension : 8 x 7.5 x 1.4
Write Your Own Review
DIY Guide to Replacing the GE WH01X26970 Ball Joint Upper
Replacing the ball joint upper on your GE washer is a relatively simple repair that can be done by most do-it-yourselfers. This guide will walk you through the steps of replacing the GE WH01X26970 ball joint upper in your washer.
Step 1: Unplug the Washer
Before beginning any repair, make sure to unplug the washer from the wall. This will prevent any electrical hazards while you are working.
Step 2: Remove the Top Panel
Using a screwdriver, remove the screws located at the back of the top panel and lift it off to access the internal components.
Step 3: Disconnect the Wiring Harness
Locate the wiring harness attached to the ball joint upper. Disconnect the harness by pulling out the two push connectors on either side of the electrical connections.
Step 4: Remove the Ball Joint Upper
Using an adjustable wrench, loosen the nut holding the ball joint upper in place. Once the nut is loose, pull the ball joint upper out from its mounting bracket.
Step 5: Install the New Ball Joint Upper
Carefully slide the new ball joint upper into the mounting bracket and secure it with the adjustable wrench. Reconnect the wiring harness to the electrical connections on the ball joint upper.
Step 6: Reattach the Top Panel
Reattach the top panel by lining up the screws and screwing them in place with a screwdriver.
Step 7: Plug in the Washer
Once all of the components are back in place, plug the washer back into the wall and make sure it is running properly.
Replacing the GE WH01X26970 ball joint upper is a relatively simple repair. With the help of this guide, you should be able to complete the repair quickly and safely.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Replacing the ball joint upper on your GE washer is a relatively simple repair that can be done by most do-it-yourselfers. This guide will walk you through the steps of replacing the GE WH01X26970 ball joint upper in your washer.
Step 1: Unplug the Washer
Before beginning any repair, make sure to unplug the washer from the wall. This will prevent any electrical hazards while you are working.
Step 2: Remove the Top Panel
Using a screwdriver, remove the screws located at the back of the top panel and lift it off to access the internal components.
Step 3: Disconnect the Wiring Harness
Locate the wiring harness attached to the ball joint upper. Disconnect the harness by pulling out the two push connectors on either side of the electrical connections.
Step 4: Remove the Ball Joint Upper
Using an adjustable wrench, loosen the nut holding the ball joint upper in place. Once the nut is loose, pull the ball joint upper out from its mounting bracket.
Step 5: Install the New Ball Joint Upper
Carefully slide the new ball joint upper into the mounting bracket and secure it with the adjustable wrench. Reconnect the wiring harness to the electrical connections on the ball joint upper.
Step 6: Reattach the Top Panel
Reattach the top panel by lining up the screws and screwing them in place with a screwdriver.
Step 7: Plug in the Washer
Once all of the components are back in place, plug the washer back into the wall and make sure it is running properly.
Replacing the GE WH01X26970 ball joint upper is a relatively simple repair. With the help of this guide, you should be able to complete the repair quickly and safely.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
