Roper Appliance Parts Dryer Parts

The Dryer Door Latch Kit includes three different door catches and two door strikes; refer to the included instructions to determine which catch and strike will fit your dryer .... If your dryer door doesn’t close properly, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Door Latch Kit• Tools Needed: Phillips-Head screwdriver, needle-nose pliers Read More Read Less

This Dryer High Limit Thermostat shuts off the heating element or burner when the dryer overheats. To determine if the thermostat is defective, use a multimeter to test it for ... continuity. This model's specifications are: 2 wire, 250 degree limit, 60 degree cool down before reset. Replacing the element will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer High Limit Thermostat• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Door Seal is a rubber gasket that prevents heat loss in the appliance during the drying cycle. If your dryer’s current seal is visibly damaged or the appliance is ...unable to maintain a constant temperature while operating, replacing this part may alleviate the issue. Replacing the seal will require basic hand tools, minor disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Required Accessory: You will need high-temperature Silicone Sealant (item WP279368) to complete this repair. Helpful Tips: This part may arrive as one piece; hold at one end and pull apart to separate before installation. Removing the dryer door before you begin will aid with proper installation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Door Seal• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Cycling Thermostat monitors and regulates the temperature inside the dryer. If the cycling thermostat is no longer working properly, you may notice that your dryer ...will not heat. Note that this part is not typically the cause of the dryer not heating; a multimeter (item 964740) can be used to test for continuity to determine if the thermostat is defective and requires replacement. Refer to the Repair Help section on the Whirlpool Parts website for additional repair information. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. The cycling thermostat is located in the back of the appliance.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Cycling Thermostat• Tools Needed: Multi screwdriver Read More Read Less

Maintain the performance of your dryer with this reliable start switch designed for a seamless fit in various appliance models. Manufactured by Whirlpool, this high-quality pa ...rt is compatible with renowned brands including Admiral, Amana, Jenn-Air, Kenmore, Kitchenaid, Magic Chef, Maytag, Norge, Roper, and Whirlpool itself. Engineered to ensure optimal functionality, this switch is essential for restoring power to your dryer, alleviating issues related to starting and operation. Whether you're a DIY enthusiast or a professional technician, installing this durable start switch is straightforward, helping you save time and repair costs. Invest in this essential component for a smoothly running dryer, keeping your laundry days worry-free. Read More Read Less

The Dryer Front Bearing and Felt Seal Kit encloses the drum in the appliance to prevent air from escaping during the drying cycle. If the seal in your dryer is worn out or dam ...aged, you may notice brown stains on your clothes after use. This is not caused by oil from the dryer; the clothes are most likely getting pinched in the drum’s holes during tumbling due to a faulty seal. As the felt seal wears out and compresses over time, it can also cause hot air to escape the drum, making the drying cycle less effective and efficient. This assembly includes (1) felt seal, (1) felt bearing, (4) locator pins and (1) tube of adhesive to complete the repair. Installing this part will require basic hand tools and disassembly of the dryer. Previous experience will be helpful but is not required to complete this repair. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this assembly. Note that you may need to trim the felt seal before installation; refer to the included instructions sheet for more information.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Front Bearing and Felt Seal Kit• Tools Needed: Multi screwdriver, putty knife Read More Read Less

The Electric Range Coil Surface Element is a 4-turn, 6" D, 1500-W plug-in style heating element. If the surface burner of your appliance no longer heats up, you may be able to ... alleviate the issue by replacing this part. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Recommended Items: If the element's terminals are corroded, you can replace them with the Element Receptacle and Wire Kit (item 330031). If more than one of your appliance’s elements are no longer working, consider purchasing the complete Coil Surface Element Kit (item 4392061). If needed, the matching 6" element (item WP660532) is also sold separately. If the stainless-steel Burner Drip Bowls of your appliance are discolored or dented, you can replace them with item W10278125.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Coil Surface Element• No tools required for installation Read More Read Less

This Dryer High Limit Thermostat protects your dryer from overheating by cutting off power if the dryer gets too hot. If the dryer won't heat, the high-limit thermostat may ha ...ve blown. This part has been updated by the manufacturer. The new thermostat may differ in appearance, but will have the same function. The part is located behind the front access panel of the dryer. When replacing, make note of the the position of the colored wires when disconnecting. Both the thermostat and fuse can be tested to determine if either is defective. Note that a multimeter (item 964740) can be used to test for continuity to determine if the thermostat is defective and requires replacement. Installing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer High Limit Thermostat• Tools Needed: Multi screwdriver Read More Read Less

This Commercial Laundry Appliance Meter Case Lock and Key Assembly includes the lock for the meter case, and the key that you turn to lock and unlock the meter case. This part ... can be used across several brands; check to see if your model number is compatible. This assembly kit includes the key and the mounting bracket. Installing this accessory will require basic hand tools and novice repair experience. Be sure to unplug the dryer and washer or shut off the house circuit breaker for the appliances before installing this kit. Also make sure you turn off your hot and cold water supplies to the washing machine.Part Specification• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Commercial Laundry Appliance Meter Case Lock and Key Assembly• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.