Maytag Appliance Parts Washer Dryer Combo Parts

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Dryer Idler Belt goes between the motor and the tumbler, and puts tension on the dryer’s drum belt. If your dryer makes a persistent squeaking sound during operation, re ...placing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Idler Belt• Tools Needed: Multi screwdriver, 5/16" nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Dryer Drum Roller Axle allows the appliance’s roller to maintain quiet and constant movement during the drying cycle. If your dryer is noisy while operating, the bearing ... in the roller may be worn out or damaged and should be replaced with this item. Installing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before you begin. Helpful Tip: While the dryer is disassembled, consider replacing the snap retaining ring and drum roller as well.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drum Roller Axle• Tools Needed: Phillips-Head screwdriver, snap-ring pliers Read More Read Less

The Electric Dryer Tri-Ring Retainer holds the drum support rollers and idler pulleys onto their shafts inside the appliance. If your dryer starts to squeal or rumble during u ...se, the current retainers may have become tangled up or overheated and the rollers and pulleys are no longer connected properly. Replacing one or more of the retainers could alleviate these issues. Note that the tri-ring retainers are sold separately. Installing this part will require basic hand tools, considerable disassembly of the dryer and intermediate repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Dryer Tri-Ring Retainer• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Door Latch Kit includes the door latch and striker assembly. If your dryer door doesn’t close properly, replacing the strike and/or catch with the contents of this ... kit may alleviate the issue. To access the part, remove the screws that hold on the front panel of the dryer, and then remove the screws that hold in the hinges of the dryer door. You'll remove the dryer door and the front panel from the dryer. Release the top panel and lean it back so you can remove the front panel assembly. The door latch lives behind the front panel assembly. Installing these parts will require basic hand tools, minor disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Door Latch Kit• Tools Needed: Multi screwdriver, 5/16" nut driver Read More Read Less

This Front Load Dryer Thermal Cut Off Fuse is a safety device designed to protect the dryer from overheating. If your dryer won't start, won't produce heat, shuts off too soon ... or won't tumble, replacing the cut off fuse may alleviate these issues. The thermal cut off is located behind the dryer's lower access panel and attaches to the exhaust duct. Several wire terminals are included for installation depending on the part number you are replacing. A multimeter can be used to test the fuse. Always check the dryer venting when replacing a blown thermal fuse. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Dryer Thermal Cut Off Fuse• Tools Needed: Multi screwdriver, putty knife, 5/16" nut driver Read More Read Less

The Dryer Heating Element Wire Connector may need to be replaced if your dryer takes too long to dry your clothes or if your dryer is no longer producing heat. To start this r ...epair, pull the dryer away from the wall to access the back panel and remove the 9 screws holding the panel in place. Remove the wire from the heating block terminal and use your wire cutters to cut off the end of the wire near the terminal. The remove about a 1/4" of insulation from the end of the wire. Then you'll connect the new wire with the new nut to the existing wire. This kit Includes (1) wire with terminal and (1) wire nut. (2) ire connectors. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Wire Splicing Tool: 8-1/4". This stripper specializes in stripping and cutting wire. This tool is designed with a lean nose for pulling and looping wire and equipped with precision ground cutters.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Dryer Heating Element Wire Connector Kit• Tools Needed: 1/4" nut driver, wire splicing tool, wire cutters Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

Whirlpool WP697813 SEALING We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!