Kitchenaid Appliance Parts

The Dryer Heating Element is strung with a coiled wire made of a nickel and a chrome alloy. If your dryer isn't heating as expected, replacing this part may alleviate the issu ...e. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer. To determine if the original part is defective before you begin the repair, use a multimeter to test for continuity. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Dryer Heating Element Kit•  Tools Needed: Multi screwdriver Read More Read Less

The Dryer Heating Element Assembly generates heat in the appliance during the drying cycle. If your dryer isn’t heating properly, check for a blown thermal fuse or thermal c ...ut out. If you see a break in the coil of your appliance’s heating element, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Dryer Heating Element Assembly•  Tools Needed: Multi screwdriver Read More Read Less

This Top Load Washer Rotor Position Sensor communicates the position of the tub’s rotor to the control board during the washing cycle. If the appliance's motor isn’t worki ...ng properly to spin the wash tub, or your washer displays an error message, replacing the rotor position sensor may alleviate these issues. To access the part, tilt the washer back letting it rest on something to support it and tape the lid down. You'll need to remove the rotor and rotor stator at the bottom of the machine. The sensor is attached to the top of the stator. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Rotor Position Sensor•  Tools Needed: Multi screwdriver, needle-nose pliers Read More Read Less

The Dryer Heating Element is a replacement part that generates heat for drying your clothes. If the coil on the element has shorted out completely, your dryer may not be creat ...ing any heat at all. If the coil shorts out and touches the metal of the element, it could cause half of the element to glow producing low heat. Be sure to check the thermal fuse on dryer before replacing the heating element. To access the part, remove the back panel from the dryer. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Dryer Heating Element•  Tools Needed: Multi screwdriver Read More Read Less

This Refrigerator Defrost Thermostat is a safety device that clips onto the evaporator in the freezer. The thermostat turns off the defrost heater in case it gets too warm in ...the freezer section. If your refrigerator does not defrost, replacing the thermostat may alleviate this issue. To access the part, open the freezer door and remove the shelves, mounting brackets (if they release), and the ice bucket. After you remove the back panel, the defrost thermostat is mounted to the end of the evaporator. Replacing the element will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Refrigerator Defrost Thermostat•  Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Refrigerator Defrost Thermostat is a safety device that clips onto the evaporator inside the freezer. The Defrost Thermostat turns off the defrost heater in case it gets ...too warm in the freezer section. To access the part, you'll have to remove all shelving, bins, rails, and mounting clips from the inside of your freezer so you can access the back panel. Remove the back panel by removing the 6 Phillips screws. Remove the light bulb cover and then lift out the back panel. Replacing the element will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Wire Splicing Tool 8-1/4". This stripper specializes in stripping and cutting wire. This tool is designed with a lean nose for pulling and looping wire and equipped with precision ground cutters.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Refrigerator Defrost Thermostat•  Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

The Ice Maker Thermistor monitors the temperature inside the appliance and sends the reading to the electronic control board. If your ice maker is making too much ice and caus ...ing the bin to overflow, replacing this part may alleviate this issue. Installing this part will require basic hand tools, some disassembly of the ice makerand novice repair experience. You must unplug the ice maker or shut off the house circuit breaker for the appliance before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Ice Maker Thermistor•  Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Top Freezer Refrigerator Temperature Control Thermostat sends power to the refrigerant system to keep the unit consistently cooled. If your refrigerator isn't maintaining ...a constant temperature, is becoming too cold or the fan is running continuously, replacing this part may alleviate these issues. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also turn off the refrigerator's water supply before you begin.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Freezer Refrigerator Temperature Control Thermostat•  Tools Needed: Multi screwdriver Read More Read Less