Washer Parts

This Direct Drive Washer Drain Pump removes water from the appliance during the drain portion of the cleaning cycle. This model is for beltless direct-drive washers and has 2 ...large ports with a backflow flapper valve. If the washer will fill and drain the water from the tub, but doesn't agitate or spin properly, replacing this part may alleviate these issues. To replace the part, remove the washer console and disconnect the lid switch to access the old part. Remove the body from the frame of the washer by tilting at a 45-degree angle and lifting it off. Place towels down to catch any water from the hoses when removed. The new pump should slide on easily –don't force it on. If you feel resistance when sliding the pump onto the shaft, you may need to remove any shaft residue left from the previous pump. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Recommended Item: Also consider replacing the washer drive motor coupler (item 285753A) at the same time you complete this repair. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Direct Drive Washer Drain Pump•  Tools Needed: Multi screwdriver, putty knife Read More Read Less

This Top Load Washer Drive Motor includes the motor and the wiring harness adapter. The drive motor has two shafts -– one shaft drives the pump, and the other shaft drives t ...he transmission. The motor causes your washer to spin, agitate, and drain properly during the washing cycle. If your washer no longer spins or agitates, replacing this part may alleviate these issues. This motor is a single speed motor (120 volt). When accessing the old motor, be sure to remove the ground wire and the base from it so you can transfer these to the new motor before installing. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Drive Replacement Motor•  Tools Needed: Multi screwdriver, putty knife, 3/16" allen wrench Read More Read Less

The Top Load Washer Agitator Dogs facilitate agitation during the cleaning cycle. If the top part of the agitator in your appliance is not moving properly but the bottom still ... functions correctly, replacing this part may alleviate the issue. This repair kit includes (4) agitator dogs. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (4) Top Load Washer Agitator Dogs•  Tools Needed: Flat blade screwdriver and socket with long extension Read More Read Less

This Top Load Washer Drain Hose measures 8' long and includes a connection clamp. The drain hose carries waste water out of the washer after the cleaning cycle. If water is le ...aking onto the floor after the washing cycle, replacing this part may alleviate the issue. You must unplug the appliance or shut off the house circuit breaker before installing. Also make sure you turn off the hot and cold water supplies.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Drain Hose•  Tools Needed: Standard pliers Read More Read Less

This Dryer Blower Wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. If your dryer is making noise ...during use or not drying your clothes as expected, replacing this part may alleviate these issues. This part is housed on the bottom, inside of the appliance and attaches to the drive motor shaft. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Dryer Blower Wheel•  Tools Needed: Multi screwdriver Read More Read Less

This Front Load Washer Door Handle in platinum (light grey) is designed for use with select models; check to see if your washer is compatible. If the current handle of your ap ...pliance is cracked, stained or broken, replacing this part may alleviate these issues. Note that the mounting screws (item WP3400805) are not included, but are available for purchase separately. Replacing this part will require no disassembly or repair experience. You must unplug the appliance or shut off the house circuit breaker before installing.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Front Load Washer Door Handle•  Tools Needed: Multi screwdriver Read More Read Less

The Front Load Dryer Tumbler Bearing Kit is in the front of the dryer and the dryer drum rides along it. The Bearing Kit helps the drum rotate smoothly and quietly. If your dr ...um is making uncommon noise during operation, replacing this part may alleviate the issue. This kit includes the bearing, a cork pad, glide, and two rivets. Note that dryers use two of these bearings in the front and both should be replaced at the same time. You'll remove the door and the front panel of your dryer to install this part. Installation of this part requires the use of a rivet gun. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Front Load Dryer Tumbler Bearing Kit•  Tools Needed: Multi screwdriver, 5/16" nut driver, rivet gun Read More Read Less

This Top Load Washer Agitator Cam Repair Kit should be used when the top part of the agitator is not moving properly but the bottom still functions correctly. This repair kit ...includes (4) agitator dogs, (1) cam, (1) bearing. Pre-assemble the repair kit before installing in the agitator. Make sure you install the dogs with the curve of the cam. We recommend using a small amount of grease (item 350849) with this kit if no grease is present on the old thrust washer. Replacing this part will require basic tools, some disassembly of the washing machine and novice repair experience. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Agitator Cam Repair Kit•  Tools Needed: Multi screwdriver, 7/16" socket Read More Read Less

The Dryer Drive Belt wraps around the motor and pulley. If your dryer's drum isn't tumbling as expected, replacing this part may alleviate the issue. To access the part, open ...the dryer door and take a putty knife around the edge of the top of your dryer and find the release clips on each side – press these in to release the top of the dryer so you can swing it open. You'll need to remove the dryer drum from the dryer cabinet to install this part. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Dryer Drive Belt•  Tools Needed: Flat-blade screwdriver, putty knife, 5/16" nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.