PA Categories

This Dryer Door Switch Assembly senses if the door of your dryer is properly closed. If your dryer does not start as expected, replacing this part may alleviate the issue. Not ...e that this part also replaces older 2-terminal switches. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Door Switch Assembly• Tools Needed: Phillips-Head screwdriver, putty knife Read More Read Less

The Dryer Drive Belt wraps around the motor and pulley. The motor rotates the belt and the belt tumbles the drum. If your dryer is noisy, won't tumble, or won't start, replaci ...ng the drive belt may alleviate these issues.To access the drive belt, first lift up the lint screen cover and remove the two screws. If you have the type of lint screen that has the cover built in, just pull it out and then remove the screws. Next, take a putty knife around the edge of the top of your dryer and find the release clips--press these in to release the top of the dryer so you can swing it open. The front panel also needs to be removed to replace the belt. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drive Belt• Tools Needed: Phillips-Head screwdriver, putty knife, 5/16" nut driver Read More Read Less

This Rear Dryer Drum Felt Seal is what seals the hot air into the dryer drum as it rotates. If hot air is leaking out of your dryer, the seal may be worn causing your dryer to ... take longer to dry your clothes. If the seal is sagging, it could pinch and mark your clothes. This seal is compatible with many different models and fits the rear drum. Includes 1 seal and adhesive to install. Replacing this part will require basic hand tools, disassembly of the dryer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Felt Drum Seal• Tools Needed: Multi screwdriver, putty knife, 5/16" nut driver Read More Read Less

The Dryer Drive Motor powers the drum in the appliance during the drying cycle. If your appliance’s drum stops turning during use or the drum won’t turn at all, replacing ...this part may alleviate these issues. This assembly includes the pulley for the dryer drum drive belt and a D-shaped shaft with two slots for wiring connectors. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Helpful Tip: If the D-shaped connector for the blower is stripped or you notice that the blower is wobbling a lot, consider also replacing it while the dryer is disassembled.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drive Motor• Tools Needed: Multi screwdriver Read More Read Less

The Front Load Dryer Drum Support Roller supports the rear of the drum on the dryer. If your dryer is making a loud rumbling or squeaking noise, replacing this part may allevi ...ate the issue. Note that both rollers should be replaced at the same time and the rollers do not need lubrication; the bearing is self-lubricating. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Dryer Drum Support Roller• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Cycling Thermostat monitors and regulates the temperature inside the dryer. If your appliance isn't heating as expected, replacing this part may alleviate the issue .... To access the part, you'll need to remove the large back panel of the dryer, then remove the wires and 1/4-inch screw that holds the old thermostat into its housing. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Cycling Thermostat• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Gas Valve Ignition Solenoid Kit is a newer style that fits all dryers with a two-coil gas valve. If your dryer does not heat or only heats intermittently, replacing ... this part may alleviate these issues. To test the coil functionality, watch the burner and if the igniter glows for awhile and then shuts off without the gas igniting. When removing the larger coil, make sure not to lose the spacer inside of it. The new coil does not include this spacer. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Valve Ignition Solenoid Kit• Tools Needed: Multi screwdriver, putty knife Read More Read Less

Hood filter works with some Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models of stoves / ovens / ranges.

• This EDR5RXD1 Water Filter (Pink) is specifically designed to diminish up to 99% of lead, ensuring enhanced safety and purity for your drinking water. • Tested ... and certified, it effectively eliminates 27 types of contaminants including lead, pesticides, pharmaceuticals, and waterborne parasites, meeting NSF standards 401, 53, and 42. • Engineered to provide water that is not only clean but also has a fresh and pure taste. • Each EVERYDROP filter replaces 1,500 plastic water bottles saved, making it an environmentally conscious option. • Used in top freezer refrigerators. Filter compartment is in the bottom left corner of the refrigerator. • Certified to fit these leading refrigerator brands: Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper. • For the best quality water, it's recommended to replace the filter every six months or 120 gallons to maximize contaminant reduction. Read More Read Less

This everydrop® Ice Filter is used in 50 LB. Ice Makers. This NSF certified filter reduces chlorine taste and odor and scale build up. Replace every 2,000 gallons (7571 liter ...s) or 9 months to ensure clean safe drinking water. The contaminants or other substances removed or reduced by this water filter are not necessarily in all users water.Part Specification• Filters should be changed every 9 months Read More Read Less