PA Categories

The Gas Dryer Igniter Kit is a flat-style igniter assembly that can be used to replace both a round or flat igniter in your appliance. The igniter lights the gas burner to hea ...t the appliance during the drying cycle. This kit includes (1) igniter assembly, (1) bracket, (2) wire nuts, (1) bolt and installation instructions. Note that the igniter is very fragile and must be handled with care. You'll remove the top and front panels of the dryer to access the part. Replacing this assembly will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Gas Dryer Igniter Kit•  Tools Needed: Multi screwdriver, putty knife Read More Read Less

This Top Load Washer Self Leveling Leg Spring is part of the self leveling leg mechanism, and attaches to the two leveling link arms to provide tension to the links. The sprin ...g is located at the back bottom of the machine hooked between two brackets. Grab it with a pair of needle-nose pliers to remove each side from the brackets. Replacing this part will require basic tools, some disassembly of the washing machine and novice repair experience. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Self Leveling Leg Spring•  Tools Needed: Needle Nose Pliers Read More Read Less

The Range Bake Igniter glows white-hot to heat properly, and lives behind the access panel at the rear of your oven. If the igniter in your oven is glowing red or orange, or n ...ot glowing at all, it may be weak and needs to be replaced. The new igniter may not have connections attached to its wire ends, so you'll have to cut the connections off of the old igniter, strip the wires, and use the included wire nuts with the new igniter. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You should unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Also be sure to turn the gas valve off before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Range Bake Igniter•  Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Gas Range Surface Igniter provides spark to the burner to ignite the gas and initiate the cooking process. This igniter features a spark electrode with a male spade conne ...ction. If your range’s igniter is no longer providing a spark to light the burner, the wire may be shorted out or the porcelain casing may be cracked. Replacing the part may alleviate these issues. Be mindful not to lose the two burner wires inside the appliance when you detach them from the old burner head. To install the new part, simply insert it into the burner head and secure it with two screws. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Gas Range Surface Igniter•  Tools Needed: Multi screwdriver, strap wrench Read More Read Less

This Top Load Washer Suspension Spring Kit is a set of 6 springs that support the washer’s outer tub and keep it stable during the cleaning cycle, including when loads are u ...nbalanced. Each spring measures approximately 7-1/2" L. You'll release the tabs from the top of the washer and remove the front panel from the machine to access the old springs. You can remove all of the springs from the front of the washer, but, you can also remove the back panel of the appliance for easier access. Apply a small amount of grease to the bottom of the new springs before you reconnect them to the washer tub. Replacing this part will require basic hand tools, some disassembly of the washing machine and novice repair experience. You must unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Suspension Spring Kit•  Tools Needed: Multi screwdriver, putty knife, standard locking pliers and lubricating grease Read More Read Less

This Whirlpool Motor Spring and Guide Kit is designed to provide maximum performance and durability. The kit includes a motor spring, guide, mounting plate and screws, bearing ... retainer and screws, and the necessary seals and gaskets to ensure your appliance runs reliably and efficiently. This kit is compatible with many models of Whirlpool washers, dryers, and other appliances. With its easy installation and long-lasting construction, you can trust that your appliance will be running smoother than ever before. Make sure your appliance is running at peak performance with this sturdy and dependable Whirlpool Motor Spring and Guide Kit. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs! Read More Read Less

The Top Load Washing Machine Balance Spring Kit, Set of 3 keeps the weight of the wash tub balanced. If the end of the spring rusts and your tub sits off balance, this part ma ...y need to be replaced. To access this part, you'll first need to remove the control panel of the washer. Usually held in place by two screws, some washer models have trim covers that need to be removed before gaining access to the screws. You'll only use one spring from this kit of three depending on the color label on your motor. Replacing this part will require basic hand tools, some disassembly of the combination washer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off your hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washing Machine Balance Spring Kit, Set of 3•  Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.