PA Categories

This Gas Range Surface Burner Spark Igniter sparks to light the oven surface burner. The most common reasons for replacing the burner spark electrodes are when the oven doesn? ...??t bake evenly, won’t heat, or won’t turn on. Replacing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Burner Spark Igniter• Tools Needed: Phillips-Head screwdriver, 1/4" nut driver Read More Read Less

The Range Surface Burner Control Knobs, Set of Four allows you to adjust the heating level of your gas cooktop surface burner. This is a set of four black knobs with double fl ...at or figure eight shaped shafts. Replacing this part will require no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Surface Burner Control Knobs, Set of Four• No tools required for installation Read More Read Less

The Range Bake Igniter glows white-hot to heat properly, and lives behind the access panel at the rear of your oven. If the igniter in your oven is glowing red or orange, or n ...ot glowing at all, it may be weak and needs to be replaced. The new igniter may not have connections attached to its wire ends, so you'll have to cut the connections off of the old igniter, strip the wires, and use the included wire nuts with the new igniter. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You should unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Also be sure to turn the gas valve off before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Bake Igniter• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Gas Range Surface Igniter provides spark to the burner to ignite the gas and initiate the cooking process. This igniter features a spark electrode with a male spade conne ...ction. If your range’s igniter is no longer providing a spark to light the burner, the wire may be shorted out or the porcelain casing may be cracked. Replacing the part may alleviate these issues. Be mindful not to lose the two burner wires inside the appliance when you detach them from the old burner head. To install the new part, simply insert it into the burner head and secure it with two screws. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Igniter• Tools Needed: Multi screwdriver, strap wrench Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Range Top Burner Control Knob, Black allows you to adjust the heating level of your gas cooktop surface burner. This knob is black with a stainless steel trim, and fits bu ...rner control knobs with 'D' shaped shafts. Remove the old knob by pulling it straight off its post. Replacing this part will require no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Top Burner Control Knob, Black• No tools required for installation Read More Read Less

This Gas Range Burner Spark Igniter is a metal conductor with ceramic insulation that delivers an electrical discharge from the spark module to the gas burner, igniting the ga ...s and lighting the flame. If the burner of your appliance no longer lights, replacing this part may alleviate the issue. Be mindful not to lose the two burner wires inside the appliance when you detach them from the old burner head. To install the new part, simply insert it into the burner head and secure it with two screws. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Burner Spark Igniter• Tools Needed: Multi screwdriver, strap wrench Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Gas Range Surface Igniter provides spark to the burner to ignite the gas and initiate the cooking process. This igniter features a spark electrode with a male spade conne ...ction. If your range’s igniter is no longer providing a spark to light the burner, the wire may be shorted out or the porcelain casing may be cracked. Replacing the igniter may alleviate these issues. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Igniter• Tools Needed: Multi screwdriver Read More Read Less

The Electric Range Surface Burner Control Knob allows you to adjust the heating level of your electric cooktop surface burner. This knob is black in color and measures 2" D. R ...eplacing this part will require no disassembly or repair experience. Make sure you unplug the oven or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Surface Burner Control Knob• No tools required for installation Read More Read Less