WE01X24546 GE Dryer Lint Filter Trap
GE WE01X24546 Trap Duct Slides allow for convenient removal and replacement of the lint filter. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!
Weight : 35.1763 lbs
Dimension : 27.5 x 25.4 x 7
GE WE01X24546 Trap Duct Slides allow for convenient removal and replacement of the lint filter. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!
Weight : 35.1763 lbs
Dimension : 27.5 x 25.4 x 7
Write Your Own Review
DIY Steps for Replacing the GE WE01X24546 Trap Duct Slides
1. Turn off the power to your dryer unit: First and foremost, you should always make sure to turn off the power to your dryer unit. Do not attempt to start any repairs until the power is definitely disconnected.
2. Gather the necessary tools and supplies: Once the power has been turned off, it's time to gather the necessary supplies and tools for the job. You need a Philips head screwdriver, small pliers, and a new GE WE01X24546 trap duct slide for the installation.
3. Remove the front panel of the dryer unit: Use your Philips head screwdriver to unscrew the two screws behind the lint filter and then pull the front panel off the dryer unit. Once removed, set the panel aside.
4. Locate and remove the existing trap duct slides: There are four trap duct slides located inside the dryer. You need to be careful when removing these, as they are made of delicate plastic. Use your small pliers to gently remove the old trap duct slides.
5. Install the new trap duct slides: Take the new GE WE01X24546 trap duct slides, and insert them into the slots on the back wall of the dryer. Make sure that the slides fit snugly and securely, and then press down firmly to ensure that they are properly installed.
6. Reassemble the dryer unit: After the new trap duct slides have been installed, you can reassemble the dryer unit by putting the front panel back in place and screwing the two screws near the lint filter.
7. Turn the power back on: Finally, turn the power back on to your dryer unit and check that the trap duct slides are working properly. If everything looks good, you can now use your dryer as usual.
By following these steps, you should have no problem replacing the GE WE01X24546 trap duct slides in your dryer. Always make sure to take all necessary safety precautions when performing repairs on any appliance.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Turn off the power to your dryer unit: First and foremost, you should always make sure to turn off the power to your dryer unit. Do not attempt to start any repairs until the power is definitely disconnected.
2. Gather the necessary tools and supplies: Once the power has been turned off, it's time to gather the necessary supplies and tools for the job. You need a Philips head screwdriver, small pliers, and a new GE WE01X24546 trap duct slide for the installation.
3. Remove the front panel of the dryer unit: Use your Philips head screwdriver to unscrew the two screws behind the lint filter and then pull the front panel off the dryer unit. Once removed, set the panel aside.
4. Locate and remove the existing trap duct slides: There are four trap duct slides located inside the dryer. You need to be careful when removing these, as they are made of delicate plastic. Use your small pliers to gently remove the old trap duct slides.
5. Install the new trap duct slides: Take the new GE WE01X24546 trap duct slides, and insert them into the slots on the back wall of the dryer. Make sure that the slides fit snugly and securely, and then press down firmly to ensure that they are properly installed.
6. Reassemble the dryer unit: After the new trap duct slides have been installed, you can reassemble the dryer unit by putting the front panel back in place and screwing the two screws near the lint filter.
7. Turn the power back on: Finally, turn the power back on to your dryer unit and check that the trap duct slides are working properly. If everything looks good, you can now use your dryer as usual.
By following these steps, you should have no problem replacing the GE WE01X24546 trap duct slides in your dryer. Always make sure to take all necessary safety precautions when performing repairs on any appliance.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
