WD15X22948 GE Dishwasher Water Inlet Valve
WD15X22948 GE Dishwasher Water Inlet Valve
Weight : 0.216500 lbs
Dimension : 4.330700 x 2.559000 x 2.716500
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
WD15X22948 GE Dishwasher Water Inlet Valve
Weight : 0.216500 lbs
Dimension : 4.330700 x 2.559000 x 2.716500
Write Your Own Review
The following parts are replaced by this product
- WD15X20326
- WD15X20239
- WD15X21339
How to Replace a GE WD15X22948 Valve Water Assembly
Replacing the GE WD15X22948 valve water assembly can help you keep your water supply running without leaks and save you money. With the right tools and materials, this is a straightforward DIY project for most homeowners. Follow these steps to replace your GE WD15X22948 valve water assembly like a pro.
Materials & Tools
• Replacement GE WD15X22948 valve water assembly
• Shut-off valves
• Adjustable wrench
• Plumber’s tape
• Bucket
• Cloth or rag
Step 1: Shut Off the Water Supply
Before you begin, shut off the water supply to the valve assembly by turning off the shut-off valves located near the water pipes. To ensure there isn’t any residual pressure in the pipes, open up all of your faucets until no more water runs out.
Step 2: Remove the Old Valve Assembly
Use an adjustable wrench to loosen and remove the compression nuts on either side of the valve assembly. As you loosen the nuts, hold the valve with your other hand so it doesn’t move. Carefully remove the valve from the water pipe.
Step 3: Clean the Pipe Fittings
Use a cloth or rag to clean the pipe fittings of any dirt and debris that might be present. This will help you get a good seal when you install the new assembly.
Step 4: Install the New Valve Assembly
Take the new GE WD15X22948 valve water assembly and wrap the threads of each of the fittings with plumber’s tape. This will help create a tight seal against any leaks. Screw the valve onto the water pipes and tighten the compression nuts by hand. Use an adjustable wrench to finish tightening the nuts securely.
Step 5: Test
Turn on the shut-off valves and check the newly installed valve water assembly for leaks. Check the pipes, valve, and fittings to make sure there are no leaks. If everything looks good, you’ve successfully replaced your GE WD15X22948 valve water assembly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Replacing the GE WD15X22948 valve water assembly can help you keep your water supply running without leaks and save you money. With the right tools and materials, this is a straightforward DIY project for most homeowners. Follow these steps to replace your GE WD15X22948 valve water assembly like a pro.
Materials & Tools
• Replacement GE WD15X22948 valve water assembly
• Shut-off valves
• Adjustable wrench
• Plumber’s tape
• Bucket
• Cloth or rag
Step 1: Shut Off the Water Supply
Before you begin, shut off the water supply to the valve assembly by turning off the shut-off valves located near the water pipes. To ensure there isn’t any residual pressure in the pipes, open up all of your faucets until no more water runs out.
Step 2: Remove the Old Valve Assembly
Use an adjustable wrench to loosen and remove the compression nuts on either side of the valve assembly. As you loosen the nuts, hold the valve with your other hand so it doesn’t move. Carefully remove the valve from the water pipe.
Step 3: Clean the Pipe Fittings
Use a cloth or rag to clean the pipe fittings of any dirt and debris that might be present. This will help you get a good seal when you install the new assembly.
Step 4: Install the New Valve Assembly
Take the new GE WD15X22948 valve water assembly and wrap the threads of each of the fittings with plumber’s tape. This will help create a tight seal against any leaks. Screw the valve onto the water pipes and tighten the compression nuts by hand. Use an adjustable wrench to finish tightening the nuts securely.
Step 5: Test
Turn on the shut-off valves and check the newly installed valve water assembly for leaks. Check the pipes, valve, and fittings to make sure there are no leaks. If everything looks good, you’ve successfully replaced your GE WD15X22948 valve water assembly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
