Dryer Parts

This Washing Machine Siphon Break Assembly is designed for use with rubber and plastic drain hose applications. This universal design is compatible with washer models; check t ...o see if your model number is compatible. The washer water siphon break provides an air gap in the drain to prevent the siphoning of dirty water back into the tub. Replacing this accessory will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off your hot and cold water supplies.Part Specification• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Washing Machine Siphon Break Assembly• Tools Needed: Screwdriver and utility shears Read More Read Less

The Dryer High Limit Thermostat is a safety device that cuts off the power to the heating element if the appliance begins to overheat. The only difference between the high lim ...it thermostat and the operating thermostat is their opening and closing temperatures. If your dryer won’t heat, this part might be defective and should be replaced. Installing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: The replacement part may look different than the original in your appliance, but the part will still install and work the same. A power screwdriver is helpful when making this repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer High Limit Thermostat• Tools Needed: Multi screwdriver Read More Read Less

This Top Load Washer Water Inlet Valve Assembly allows hot and cold water to fill in the washer. This assembly includes (1) body fill valve in blue, (1) mounting bracket, (1) ...screw and installation instructions. If your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy, replacing the water inlet valve may alleviate these issues. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve may not be working properly. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Water Inlet Valve Assembly• Tools Needed: Multi screwdriver, standard pliers Read More Read Less

This Top Load Washer Agitator Repair Kit is designed for use with select compatible washing machines. If the top part of the agitator is not moving properly in your appliance ...but the bottom still functions correctly, replacing this part may alleviate the issue. This repair kit includes (4) agitator dogs, (1) medium length cam, (1) cap seal, (1) washer for the agitator bolt and (1) thrust washer. We recommend using a small amount of grease (item 350849) with this kit if no grease is present on the old thrust washer. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation. Recommended Item: Also consider replacing the bolt (item 539455) and getting a spare set of dog ears (item 3109). The bolt can get corroded and the dog ears wear out over time.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Washer Agitator Repair Kit• Tools Needed: Flat-blade screwdriver, 7/16 in. socket with long extension Read More Read Less

The Gas Dryer Flame Sensor reacts to the heat from the ignitor, allowing the gas valve to open and the dryer to create heat. If your appliance isn't heating as expected during ... operation, replacing this part may alleviate the issue. This sensor is located across from the gas igniter at the dryer’s burner assembly and should be closed for continuity at room temperature. Be sure to check for continuity with a multimeter before installing a new sensor. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Recommended Item: While the dryer is disassembled, consider replacing the gas valve coils (item 279834) as well.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Flame Sensor• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Door Latch Kit includes three different door catches and two door strikes; refer to the included instructions to determine which catch and strike will fit your dryer .... If your dryer door doesn’t close properly, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Door Latch Kit• Tools Needed: Phillips-Head screwdriver, needle-nose pliers Read More Read Less

This Dryer Vent Kit connects the dryer exhaust port to your home's external exhaust vent. The kit may include multiple parts; refer to your parts diagram for a complete list o ...f parts included. Vent kit includes (2) 4-ft flexible vent pieces, (2) close-quarter elbows, and clamps. This is a universal accessory that can be used across several brands; check to see if your model number is compatible. Installing this accessory will require basic hand tools and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Dryer Vent Kit• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Front Bearing and Felt Seal Kit encloses the drum in the appliance to prevent air from escaping during the drying cycle. If the seal in your dryer is worn out or dam ...aged, you may notice brown stains on your clothes after use. This is not caused by oil from the dryer; the clothes are most likely getting pinched in the drum’s holes during tumbling due to a faulty seal. As the felt seal wears out and compresses over time, it can also cause hot air to escape the drum, making the drying cycle less effective and efficient. This assembly includes (1) felt seal, (1) felt bearing, (4) locator pins and (1) tube of adhesive to complete the repair. Installing this part will require basic hand tools and disassembly of the dryer. Previous experience will be helpful but is not required to complete this repair. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this assembly. Note that you may need to trim the felt seal before installation; refer to the included instructions sheet for more information.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Front Bearing and Felt Seal Kit• Tools Needed: Multi screwdriver, putty knife Read More Read Less

The Gas Dryer Igniter Kit is a flat-style igniter assembly that can be used to replace both a round or flat igniter in your appliance. This kit includes (1) ignitor assembly, ...(1) bracket, (2) wire nuts and (1) mounting screw. If the dryer does not heat or heats intermittently, replacing this part may alleviate these issues. Note that this igniter is fragile and you cannot touch the grey section of the part; only handle the igniter by its white plastic covering. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Helpful Tip: While the dryer is disassembled, consider replacing the gas valve coils (item 279834) as well.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Igniter Kit• Tools Needed: Multi screwdriver and wrench Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.