Maytag Appliance Parts Washer Dryer Combo Parts Igniter

The Gas Dryer Igniter Kit is a flat-style igniter assembly that can be used to replace both a round or flat igniter in your appliance. This kit includes (1) Igniter assembly, ...(1) bracket, (2) wire nuts and (1) mounting screw. If the dryer does not heat or heats intermittently, replacing this part may alleviate these issues. Note that this igniter is fragile and you cannot touch the grey section of the part; only handle the igniter by its white plastic covering. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Helpful Tip: While the dryer is disassembled, consider replacing the gas valve coils (item 279834) as well.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Igniter Kit• Tools Needed: Multi screwdriver and wrench Read More Read Less

The Gas Dryer Igniter lights the gas in your dryer. If your dryer is no longer supplying heat, this part may be damaged or cracked and may need to be replaced. To access the p ...art, lift the top of the dryer by releasing the spring clips from the top panel with a putty knife. Then remove the door switch wires and the screws that release the front panel. Next, simply loosen the screw that holds in the igniter to remove it. Please note that the bracket is no longer included with this part. If your original igniter was round, also order bracket (item 37001309). Replacing this assembly will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Note that you cannot touch the grey part of the igniter; only handle the igniter by its white plastic covering.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Igniter Kit• Tools Needed: Multi screwdriver, putty knife, 5/16" wrench Read More Read Less

The Gas Dryer Igniter Kit is a flat-style igniter assembly that can be used to replace both a round or flat igniter in your appliance. The igniter lights the gas burner to hea ...t the appliance during the drying cycle. This kit includes (1) igniter assembly, (1) bracket, (2) wire nuts, (1) mounting screw and installation instructions. Note that the igniter is very fragile and must be handled with care. Replacing this assembly will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Igniter Kit• Tools Needed: Multi screwdriver, putty knife Read More Read Less

This Dryer Moisture Sensor Bar monitors the moisture levels of the clothing during the drying cycle and communicates a signal to the control board indicating when the clothes ...are dry and the cycle can finish. If your appliance shuts off too early or continues running after the clothes are already dry, one or more of the dryer’s moisture sensors may be defective and need replacement. Note that your appliance requires two sensor bars to operate properly; the parts are sold separately. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. The sensors are located in the plastic lint screen housing.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Moisture Sensor Bar• Tools Needed: Multi screwdriver Read More Read Less