Amana Appliance Parts

This Top Load Washer Rotor Position Sensor communicates the position of the tub’s rotor to the control board during the washing cycle. If the appliance's motor isn’t worki ...ng properly to spin the wash tub, or your washer displays an error message, replacing the rotor position sensor may alleviate these issues. To access the part, tilt the washer back letting it rest on something to support it and tape the lid down. You'll need to remove the rotor and rotor stator at the bottom of the machine. The sensor is attached to the top of the stator. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Rotor Position Sensor• Tools Needed: Multi screwdriver, needle-nose pliers Read More Read Less

The Ice Maker Thermistor monitors the temperature inside the appliance and sends the reading to the electronic control board. If your ice maker is making too much ice and caus ...ing the bin to overflow, replacing this part may alleviate this issue. Installing this part will require basic hand tools, some disassembly of the ice makerand novice repair experience. You must unplug the ice maker or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Ice Maker Thermistor• Tools Needed: Multi screwdriver Read More Read Less

This Dishwasher Access Panel Retainer, Black, holds the protective panel along the bottom of the dishwasher in place. If one or more of the appliance’s plastic retainers are ... cracked or broken, you can easily replace them with this part. Installing this part will require basic hand tools and no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dishwasher Access Panel Retainer, Black• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Washer Outer Door Boot Seal Clamp holds the washer bellow seal (door boot) in place in the appliance's frame. If the existing part is broken, rusted or missing, replacing ...this part may alleviate the issue. The clamp measures approx. 16-1/2" D and is sold separately. Replacing this part will require basic hand tools, minor disassembly of the washer and novice repair experience. You must unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Also consider replacing the Washer Door Boot Seal (item WP8182119) at the same time you complete this repair. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Washer Outer Door Boot Seal Clamp• Tools Needed: Multi screwdriver Read More Read Less

The Gas Range Surface Burner Igniter Clip holds the surface burner igniter in place. If the existing clip in your appliance is broken and no longer holding the igniter properl ...y, replacing this part may alleviate the issue. To access the part, remove your burner grates, burners and burner caps. Then remove the burner screws. Use a putty knife under the stove top to release the locking clips holding it in place and then lift up the top of the range. Each clip is sold separately. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Burner Igniter Clip• Tools Needed: Multi screwdriver, channel locks, needle nose pliers, putty knife Read More Read Less

The SxS Refrigerator Temperature Sensor detects the temperature inside the refrigerator and sends this information to the electronic control. If the fresh food section of your ... appliance is not maintaining the desired temperature, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Temperature Sensor• Tools Needed: Multi screwdriver, tape and wire splicing tool Read More Read Less

The Ice Maker Thermistor monitors the temperature inside the appliance and sends the reading to the electronic control board. If your ice maker is making too much ice and caus ...ing the bin to overflow, replacing this part may alleviate this issue. Installing this part will require basic hand tools, some disassembly of the ice maker and novice repair experience. You must unplug the ice maker or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Ice Maker Thermistor• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.