PA Categories

The Gas Range Surface Burner Igniter Clip holds the surface burner igniter in place. If the existing clip in your appliance is broken and no longer holding the igniter properl ...y, replacing this part may alleviate the issue. To access the part, remove your burner grates, burners and burner caps. Then remove the burner screws. Use a putty knife under the stove top to release the locking clips holding it in place and then lift up the top of the range. Each clip is sold separately. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Burner Igniter Clip• Tools Needed: Multi screwdriver, channel locks, needle nose pliers, putty knife Read More Read Less

The Range Surface Control Knob allows you to control the size of the flame coming from your cooktop burner. This stainless steel knob is approximately 2" in diameter and is so ...ld individually. Replacing this part will require no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Surface Control Knob• No tools required for installation Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. Remove the rear ac ...cess panel to access the old sensor. Depress the tab to disconnect the sensor wire connector. unscrew the sensor mounting screw and pull out the old sensor. Insert the new sensor into the hole of the rear panel and replace the mounting screw to secure. Reconnect the wire connector and secure the access panel back into place. Installing this part will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing. Also make sure to shut off the gas.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

Whirlpool WPW10299227 Hinge-Door. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!

This Top Load Washer Clutch Assembly drives the drum during the spin portion of the wash cycle. If your clothes are still soaked after spinning, replacing this part may allevi ...ate the issue. This kit includes (1) clutch assembly, (1) brake cam driver, (2) springs, (1) retaining ring, (1) baring and installation instructions. Note that the blue spring should be used in large-capacity washers; the black spring is for use in compact washing machines. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Recommended Item: The appliance's Repair Manual (item 4313896) is a useful reference when replacing this part. Helpful Tip: Also consider replacing the motor coupling (item 1195967) while you have the washing machine’s cabinet removed. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Clutch Assembly• Tools Needed: Multi screwdriver, needle-nose pliers Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Dryer High Limit Thermostat and Fuse Kit regulates the temperature of the dryer stopping it from overheating. If your dryer does not heat as expected, replacing this part ... alleviate the issue. The part is located behind the front access panel of the dryer. When replacing, make note of the the position of the colored wires when disconnecting. Both the thermostat and fuse can be tested to determine if either is defective before you begin the repair. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer High Limit Thermostat and Fuse Kit• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Drum Belt circles the dryer’s entire drum and attaches it to the motor to create constant spinning during the drying cycle. If your dryer’s motor is running but ...the drum isn’t turning, replacing this part may alleviate the issue. This part features 5 ribs with 4 grooves. When replacing the part, make sure the belt is aligned on the high part of the drum to prevent damage to the idler pulley guide arm. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Recommended Item: While the dryer is disassembled, also consider replacing the idler pulley (item W10116792).Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drum Belt• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Drum Support Roller is what supports the rear of the drum on the dryer. If the appliance is making a loud rumbling or squeaking noise, replacing this part may allev ...iate the issue. Note that both rollers should be replaced at the same time, and the rollers do not need lubrication. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) roller and (2) washers• Tools Needed: Snap ring pliers Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.