4280EN4001G LG Washer Rear Tub Ball Bearing
Washer rear tub ball bearing for some models of LG washing machines.
Weight : 0.0408 lbs
Dimension : 3.05 x 3.05 x 0.85
Washer rear tub ball bearing for some models of LG washing machines.
Weight : 0.0408 lbs
Dimension : 3.05 x 3.05 x 0.85
Write Your Own Review
DIY Guide on Replacing the 4280EN4001G LG Washer Rear Tub Ball Bearing
If you own a LG Washer with model number 4280EN4001G, and you’re experiencing excessive noise during operation, then it may be time to replace the rear tub ball bearing. The good news is that this process is easy and can be done quickly with the right tools and supplies. Here's a step-by-step guide on how to replace the 4280EN4001G LG Washer Rear Tub Ball Bearing.
What You'll Need:
New LG 4280EN4001G Rear Tub Ball Bearing
Socket wrench
7/32-inch Allen Wrench
Screwdriver
Step 1: Unplug Washer
Start by unplugging your LG washer from the wall outlet. This is for safety purposes and will ensure that the machine does not become activated during the repair process.
Step 2: Disconnect Drain Hose
To access the rear of the washer, the drain hose needs to be disconnected. Find the drain hose at the bottom of the appliance and use a screwdriver to loosen the clamps. Carefully pull the hose away from the washer to disconnect it.
Step 3: Remove Washer Top
Using a socket wrench, carefully unscrew and remove the screws located at the back of the washer top. Gently lift the top of the washer off to access the interior of the machine.
Step 4: Remove Thor Bolt
Once you’ve accessed the interior of the LG washer, locate the Thor bolt at the rear. This is a long, metal bolt that fastens the rear tub bearing to the frame. Using the socket wrench, carefully remove the Thor bolt and set it aside.
Step 5: Remove Old Bearing
Next, carefully remove the old bearing from the rear of the frame. Use the 7/32-inch Allen wrench to unscrew the nut that holds the bearing in place. Once the nut is removed, gently pull the bearing from the frame.
Step 6: Install New Bearing
Now it’s time to install the new rear tub bearing. Place the new bearing in the frame and secure it using the 7/32-inch Allen wrench. Make sure the bearing is secure and properly aligned with the frame before continuing.
Step 7: Reinstall Thor Bolt
With the new bearing in place, reinstall the Thor bolt. Use the socket wrench to carefully tighten the Thor bolt until it’s secure. Make sure the bolt is tightly fastened to the frame before moving on to the next step.
Step 8: Reattach Drain Hose
Finally, reattach the drain hose to the bottom of the washer. Use a screwdriver to tighten the clamps on the hose and ensure a secure connection.
After completing these steps, your 4280EN4001G LG Washer should be ready to go. Be sure to turn the machine on to make sure it is operating correctly and there is no excessive noise. If everything is working properly, you have successfully replaced the 4280EN4001G LG Washer Rear Tub Ball Bearing.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
If you own a LG Washer with model number 4280EN4001G, and you’re experiencing excessive noise during operation, then it may be time to replace the rear tub ball bearing. The good news is that this process is easy and can be done quickly with the right tools and supplies. Here's a step-by-step guide on how to replace the 4280EN4001G LG Washer Rear Tub Ball Bearing.
What You'll Need:
New LG 4280EN4001G Rear Tub Ball Bearing
Socket wrench
7/32-inch Allen Wrench
Screwdriver
Step 1: Unplug Washer
Start by unplugging your LG washer from the wall outlet. This is for safety purposes and will ensure that the machine does not become activated during the repair process.
Step 2: Disconnect Drain Hose
To access the rear of the washer, the drain hose needs to be disconnected. Find the drain hose at the bottom of the appliance and use a screwdriver to loosen the clamps. Carefully pull the hose away from the washer to disconnect it.
Step 3: Remove Washer Top
Using a socket wrench, carefully unscrew and remove the screws located at the back of the washer top. Gently lift the top of the washer off to access the interior of the machine.
Step 4: Remove Thor Bolt
Once you’ve accessed the interior of the LG washer, locate the Thor bolt at the rear. This is a long, metal bolt that fastens the rear tub bearing to the frame. Using the socket wrench, carefully remove the Thor bolt and set it aside.
Step 5: Remove Old Bearing
Next, carefully remove the old bearing from the rear of the frame. Use the 7/32-inch Allen wrench to unscrew the nut that holds the bearing in place. Once the nut is removed, gently pull the bearing from the frame.
Step 6: Install New Bearing
Now it’s time to install the new rear tub bearing. Place the new bearing in the frame and secure it using the 7/32-inch Allen wrench. Make sure the bearing is secure and properly aligned with the frame before continuing.
Step 7: Reinstall Thor Bolt
With the new bearing in place, reinstall the Thor bolt. Use the socket wrench to carefully tighten the Thor bolt until it’s secure. Make sure the bolt is tightly fastened to the frame before moving on to the next step.
Step 8: Reattach Drain Hose
Finally, reattach the drain hose to the bottom of the washer. Use a screwdriver to tighten the clamps on the hose and ensure a secure connection.
After completing these steps, your 4280EN4001G LG Washer should be ready to go. Be sure to turn the machine on to make sure it is operating correctly and there is no excessive noise. If everything is working properly, you have successfully replaced the 4280EN4001G LG Washer Rear Tub Ball Bearing.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
