Maytag Appliance Parts Valve & Float

The Dishwasher Water Inlet Valve allows the appliance to fill with water and complete the cleaning cycle. If your dishwasher won't fill properly or overflows and leaks water o ...n the floor, then the water valve may be restricted or damaged and replacing it may alleviate these issues. Note that if the dishwasher is underfilling, it will most likely exhibit poor wash performance. In order to access the part, you'll remove the lower access panel from the dishwasher. Note that you will need to reuse the brass fitting from the existing part with the new valve; use pipe joint compound to securely attach it to the new part.Replacing this part will require basic hand tools, some disassembly of the dishwasher and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Also be sure to turn off the water supply to your dishwasher before you begin. Helpful Tip: We also recommend using affresh® Dishwasher Cleaner* (item W10282479) to help reduce limescale and mineral build-up that can be unsightly and affect your dishwasher’s performance.*affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dishwasher Water Inlet Valve• Tools Needed: Multi screwdriver, channel lock pliers Read More Read Less

The French Door Refrigerator Water Inlet Valve allows water to enter the refrigerator’s water dispenser and ice maker. If one of the solenoids in the original unit is bad, i ...t will prevent water from flowing into the ice maker and dispenser. If the icemaker of your appliance stops making ice, no water flows from the dispenser or it flows constantly, or if you notice water at the bottom of the fresh food compartment, the water inlet valve could be malfunctioning and need to be replaced. Installing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also turn off the refrigerator’s water supply before you begin. Helpful Tip: We do not recommend disassembling your appliance’s current water inlet valve to clean it due to the risk of failure after the repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) French Door Refrigerator Water Inlet Valve• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The SxS Refrigerator Water Inlet Valve allows water to enter the refrigerator’s water dispenser and ice maker. The package includes the new inlet water valve, instructions, ...¼" tubing and a plastic ¼" coupler. If water isn't entering the ice maker and dispenser in your appliance, replacing this part may alleviate the issue. The new part's wire connections are on the back of the unit and the valve includes a "push to lock" fitting that doesn't require a nut to attach the tubing. You'll have to remove the old style compression fittings around the water line and trim, then push the water line directly into the valve where it will lock into place. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also turn off the refrigerator's water supply before you begin.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Water Inlet Valve Assembly• Tools Needed: Multi screwdriver Read More Read Less

This Top Load Washer Water Inlet Valve opens to allow water to enter the washing machine. The attaching solenoids on the valve open and close according to the desired temperat ...ure, or amount of water needed. If your washer won't stop filling with water, won't produce cold or hot water, won't fill at all, or is leaking, replacing the inlet valve may alleviate these issues.This inlet valve has 4 terminals and is located at the back of the machine. To access the part, you'll need to separate the washer cabinet from the washer and disconnect the red and white wiring connectors from the old part. Recommended Item: Washer Fill Hose (item 8212487RP). Package of two 5' industrial braid hoses with pre-installed washers and straight ends. We recommend replacing washing machine inlet hoses after 5 years of use to reduce the risk of hose failure. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Water Inlet Valve Assembly• Tools Needed: Multi screwdriver, needle-nose pliers Read More Read Less

VALVE

This Washer Water Inlet Valve controls the water flow into the washer. If your washer isn’t getting any hot or cold water, replacing this part may alleviate the issue. Repla ...cing this part will require basic hand tools, some disassembly of the washing machine and novice repair experience. You must unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Recommended Item: Consider replacing the Fill Hose (item 8212487RP) at the same time you complete this repair. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Washer Water Inlet Valve• Tools Needed: Multi screwdriver, 10" V-Jaw Tongue & Groove Pliers, tape, putty knife, standard pliers, nylon lanyard Read More Read Less

This Top Load Washer Water Inlet Valve is located at the rear of the appliance and allows hot and cold water to fill in the washer during the cleaning cycle. If your washer is ...n’t getting any cold or hot water, one of the solenoids in the appliance's current valve may have failed. This part may also be needed if you find that your washer is filling slowly, not filling at all or leaking cold or hot water onto the floor. Replacing this part will require basic hand tools, some disassembly of the washing machine and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off your hot and cold water supplies. Recommended Item: Consider replacing the Fill Hose (item 8212487RP) at the same time as this repair. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Water Inlet Valve• Tools Needed: Multi screwdriver, putty knife Read More Read Less