Maytag Appliance Parts

This Refrigerator Defrost Thermostat is a safety device that clips onto the evaporator in the freezer. The thermostat turns off the defrost heater in case it gets too warm in ...the freezer section. If your refrigerator does not defrost, replacing the thermostat may alleviate this issue. To access the part, open the freezer door and remove the shelves, mounting brackets (if they release), and the ice bucket. After you remove the back panel, the defrost thermostat is mounted to the end of the evaporator. Replacing the element will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Defrost Thermostat• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Refrigerator Defrost Thermostat is a safety device that clips onto the evaporator inside the freezer. The Defrost Thermostat turns off the defrost heater in case it gets ...too warm in the freezer section. To access the part, you'll have to remove all shelving, bins, rails, and mounting clips from the inside of your freezer so you can access the back panel. Remove the back panel by removing the 6 Phillips screws. Remove the light bulb cover and then lift out the back panel. Replacing the element will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Wire Splicing Tool 8-1/4". This stripper specializes in stripping and cutting wire. This tool is designed with a lean nose for pulling and looping wire and equipped with precision ground cutters.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Defrost Thermostat• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Top Freezer Refrigerator Temperature Control Thermostat sends power to the refrigerant system to keep the unit consistently cooled. If your refrigerator isn't maintaining ...a constant temperature, is becoming too cold or the fan is running continuously, replacing this part may alleviate these issues. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also turn off the refrigerator's water supply before you begin.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Freezer Refrigerator Temperature Control Thermostat• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Cycling Thermostat monitors and regulates the temperature inside the dryer. If your appliance isn't heating as expected, replacing this part may alleviate the issue .... To access the part, you'll need to remove the large back panel of the dryer, then remove the wires and 1/4-inch screw that holds the old thermostat into its housing. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Cycling Thermostat• Tools Needed: Multi screwdriver Read More Read Less

This Gas Range Spark Module creates the spark for lighting the gas for the range's surface burners. To access the part, you’ll need to remove the large panel on the rear of ...the range's console. Note that transferring the wires from the old part to the new part one at a time will help prevent incorrect installation. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure to turn the gas valve off before the repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Burner Spark Module• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Range Surface Burner Spark Module produces sparks that ignite the top gas burners on your range. If one or more of your top burners won't spark, replacing the module may ...alleviate this issue. This kit includes the (1) module, (1) mounting bracket, (2) connectors, (1) Phillips screw. The terminals supplied should not be used if they are different in size than the current terminals. To access the part, you'll remove the back panel of your range. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Surface Burner Spark Module Kit• Tools Needed: Multi screwdriver, needle nose pliers, 1/4" nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.