Maytag Appliance Parts

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Refrigerator Defrost Thermostat is a safety device that clips onto the evaporator inside the freezer. The Defrost Thermostat turns off the defrost heater in case it gets ...too warm in the freezer section. To access the part, you'll have to remove all shelving, bins, rails, and mounting clips from the inside of your freezer so you can access the back panel. Remove the back panel by removing the 6 Phillips screws. Remove the light bulb cover and then lift out the back panel. Replacing the element will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Wire Splicing Tool 8-1/4". This stripper specializes in stripping and cutting wire. This tool is designed with a lean nose for pulling and looping wire and equipped with precision ground cutters.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Defrost Thermostat• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Freezer Door Gasket is on the inner door panel of your freezer and creates a seal around the door to prevent warm air from entering the freezer. If this gasket is worn ou ...t, cold air will leak out of the freezer. As a result, the freezer may run longer in an attempt to cool down, or frost may accumulate. This gasket comes in white. To remove any creases or wrinkles from the new gasket, set it in the sun or hot water for a few minutes. Installing this part will require little disassembly or repair experience. Also be sure to remove any items sitting in your freezer, since you'll need to remove the door to replace this part. Make sure you unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Freezer Door Gasket• Tools Needed: Multi screwdriver Read More Read Less

This Gas Range Spark Ignition Module creates the spark for lighting the gas for the range's surface burners. If your gas range burners aren't lighting as expected, replacing t ...his part may alleviate the issue. To access the part, you’ll need to remove the large panel on the rear of the range's console. Note that transferring the wires from the old part to the new part one at a time will help prevent incorrect installation. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the gas range or shut off the house circuit breaker for the appliance before installing this part. Also make sure to turn the gas valve off before the repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Spark Ignition Module• Tools Needed: Multi screwdriver Read More Read Less

The Front Load Dryer Lint Screen is a white screen that provides proper air flow and operation of your dryer. After pulling the old filter out, be sure to clean the channels o ...f the lint housing before inserting the new lint screen. The filter should be cleaned before every load of laundry and replaced immediately if damaged. This a replacement lint filter with handle. Replacing your dryer’s lint filter is a quick and essential way to keep your appliance operating at optimal levels. Installing this part requires no tools, disassembly or repair experience. Recommended Tool: The Cleaning Brush (item 4210463RW) is useful to remove lint and other debris from the dryer’s venting.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Dryer Lint Screen• No tools required for installation Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.