Maytag Appliance Parts

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

GAS TIMER W/ SEAL

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The SxS Refrigerator Ice Dispenser Chute Door opens to allow ice to pass through the dispenser and closes to prevent ice from dropping out of the refrigerator onto the floor. ...If your appliance’s current chute door isn’t opening and closing properly, you can easily replace the defective part with this item. Note that this part no longer uses a ribbon heater due to an improved foam design. Installing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Ice Dispenser Chute Door• Tools Needed: Multi screwdriver, putty knife Read More Read Less

The Electric Dryer Tri-Ring Retainer holds the drum support rollers and idler pulleys onto their shafts inside the appliance. If your dryer starts to squeal or rumble during u ...se, the current retainers may have become tangled up or overheated and the rollers and pulleys are no longer connected properly. Replacing one or more of the retainers could alleviate these issues. Note that the tri-ring retainers are sold separately. Installing this part will require basic hand tools, considerable disassembly of the dryer and intermediate repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Dryer Tri-Ring Retainer• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Top Load Washer Leveling Leg is a metal replacement part that allows your appliance to sit perfectly flat. A stop nut is also included with this item. Install the new lev ...eling leg and test to see if you have it adjusted properly by putting the appliance on all four legs. Adjust the new part in or out as required if your washer is unsteady. Note that you may need assistance tilting and balancing the appliance while completing this repair. Replacing this part will require basic hand tools, but no disassembly or repair experience. Helpful Tip: We recommend checking the other three leveling legs on your appliance in case they are also damaged or worn and require replacement.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Leveling Leg• Tools Needed: Standard pliers Read More Read Less

This Dryer High Limit Thermostat protects your dryer from overheating by cutting off power if the dryer gets too hot. If the dryer won't heat, the high-limit thermostat may ha ...ve blown. This part has been updated by the manufacturer. The new thermostat may differ in appearance, but will have the same function. The part is located behind the front access panel of the dryer. When replacing, make note of the the position of the colored wires when disconnecting. Both the thermostat and fuse can be tested to determine if either is defective. Note that a multimeter (item 964740) can be used to test for continuity to determine if the thermostat is defective and requires replacement. Installing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer High Limit Thermostat• Tools Needed: Multi screwdriver Read More Read Less