Maytag Appliance Parts

The SxS Refrigerator Water Inlet Valve allows water to enter the refrigerator’s water dispenser and ice maker. If the icemaker of your appliance stops making ice, the ice cu ...bes are small or hollow, no water flows from the dispenser or it flows constantly, or if you notice water at the bottom of the fresh food compartment, replacing this part may alleviate these issues. The package includes (1) inlet water valve, (1) plastic tube, (1) plastic union and installation instructions. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also turn off the refrigerator's water supply before you begin.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Water Inlet Valve• Tools Needed: Multi screwdriver Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. Remove the rear ac ...cess panel to access the old sensor. Depress the tab to disconnect the sensor wire connector. unscrew the sensor mounting screw and pull out the old sensor. Insert the new sensor into the hole of the rear panel and replace the mounting screw to secure. Reconnect the wire connector and secure the access panel back into place. Installing this part will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing. Also make sure to shut off the gas.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Idler Pulley and Bracket sits between the motor and the drum of the dryer, putting tension on the drive belt. If your appliance is no longer spinning as expected, r ...eplacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Recommended Part: When installing this part, also consider also replacing the Drive Belt (item #661570V). The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Idler Pulley and Bracket Assembly• Tools Needed: Multi screwdriver Read More Read Less

W10754161 Whirlpool Rotor Assembly

This Top Load Washer Lid Lock Assembly prevents the washer lid from opening during the wash cycle and spin cycle. If the lid of your appliance won’t stay locked or the curre ...nt lid lock is cracked or damaged, replacing this part may alleviate these issues. In order to access the part, you'll need to release the control panel. It may be easier to release the control panel clips by releasing the top first then accessing the clips from underneath. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Lid Lock Assembly• Tools Needed: Multi screwdriver Read More Read Less

The Door Gasket is a grey rubber seal on the inner door panel of your freezer that creates a seal around the door to prevent warm air from entering the freezer compartment. To ... remove any creases or wrinkles from the new gasket, set it in the sun or hot water for a few minutes. Safely store any food that could deteriorate while the door is open for this repair. To remove the old seal, remove the screws holding in the freezer door and lay it on a flat surface. Use a flat blade screwdriver to pry out the old seal from the door. If you install the gasket and it isn't lying flat with your refrigerator door closed, you can safely mold it with a heat gun--but be careful not to melt it. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Door Gasket• Tools Needed: Multi screwdriver, heat gun Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Top Load Washer Basket Drive Hub connects the spin basket to the spin shaft that spins the basket. If your washing machine isn't spinning as expected, replacing this part ...may alleviate the issue. To access the part, you'll first need to remove the agitator or the impeller depending on your washer model. Then remove the screws holding in the old drive hub and the driver hub. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Basket Drive Hub Kit• Tools Needed: Multi screwdriver, socket Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.