Magic Chef Appliance Parts

The Dryer Drive Belt wraps around the motor and pulley and rotates the belt and the belt tumbles the drum. If the drum of your appliance isn't operating as expected, replacing ... this part may alleviate the issue. To access the part, first lift up the lint screen cover and remove the two screws. If you have the type of lint screen that has the cover built in, just pull it out and then remove the screws. Next, take a putty knife around the edge of the top of your dryer and find the release clips--press these in to release the top of the dryer so you can swing it open. The front panel also needs to be removed to replace the belt. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drum Belt• Tools Needed: Phillips-Head screwdriver, 5/16" nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Dishwasher Pump Impeller Kit is a rebuild for the pump in your dishwasher. If your pump is damaged and you aren't getting any water pressure, or the water seal is damaged ... and water is draining outside of the dishwasher, this part may need to be replaced. Remove the lower rack of your dishwasher and take out the spray arm nut by turning it counter-clockwise to access the part. When removing the old gasket, be sure to clean out any left behind residue. This kit includes the drain & wash impeller, pump seal, chopper, spacer, water seal, spring, hold down bolt, and instruction sheet.Replacing this part will require basic hand tools, some disassembly of the dishwasher and novice repair experience. You must unplug the dishwasher or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the dishwasher's hot and cold water supplies underneath the sink.Helpful Tip: We also recommend using affresh® Dishwasher Cleaner (item W10282479) to help remove limescale and mineral build-up that can be unsightly and affect your dishwasher’s performance. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dishwasher Pump Impeller Kit• Tools Needed: Multi screwdriver, torque 15 driver, adjustable wrench, 1/4" nut driver Read More Read Less

This Front Load Dryer Thermal Cut Off Fuse is a safety device designed to protect the dryer from overheating. If your dryer won't start, won't produce heat, shuts off too soon ... or won't tumble, replacing the cut off fuse may alleviate these issues. The thermal cut off is located behind the dryer's lower access panel and attaches to the exhaust duct. Several wire terminals are included for installation depending on the part number you are replacing. A multimeter can be used to test the fuse. Always check the dryer venting when replacing a blown thermal fuse. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Dryer Thermal Cut Off Fuse• Tools Needed: Multi screwdriver, putty knife, 5/16" nut driver Read More Read Less

The Ice Maker Thermistor monitors the temperature inside the appliance and sends the reading to the electronic control board. If your ice maker is making too much ice and caus ...ing the bin to overflow, replacing this part may alleviate this issue. Installing this part will require basic hand tools, some disassembly of the ice maker and novice repair experience. You must unplug the ice maker or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Ice Maker Thermistor• Tools Needed: Multi screwdriver Read More Read Less

Whirlpool WP8564458 ABSORBER WASHER SOUND. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!

The SxS Refrigerator Water Inlet Valve allows water to enter the refrigerator’s water dispenser and ice maker. The package includes a new water valve, instructions, ¼" tubi ...ng and a plastic union. Remove the cardboard back from the bottom of the refrigerator to access this part and remove the copper tubing. Place a towel down to catch any dripping water. The old valve has screw on compression fittings, whereas the new valve has press and lock fittings. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also, be sure to turn off the refrigerator’s water supply. Helpful Tip: Some refrigerator models also require a separate connection fitting (Tubing Coupler, item 2119001).Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Water Inlet Valve• Tools Needed: Multi screwdriver, 1/2" wrench and nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.