Amana Appliance Parts

This Gas Range Surface Burner Valve controls the flow of gas to the surface burner on your range. Once this valve senses the desired heat, it will open up and allow the gas to ... travel to the oven burner. If you are no longer getting heat to the burners, you may need to replace the valve. Installing this part will require specialized tools, complicated disassembly of the oven and prior repair experience. We recommend that you hire a qualified technician to install this assembly. If installing yourself, remember to unplug the oven or shut off the house circuit breaker and gas valve for the appliance before beginning.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Burner Valve• Tools Needed: Specialized Tools Read More Read Less

The Gas Dryer Valve Coil opens the gas valves while the dryer is running. If gas isn't flowing and your dryer has no heat, or it's cycling on and off repeatedly, replacing the ... coil may alleviate these issues. This set has a boost hold coil (3 prong) and secondary coil (2 prong). You can use a multimeter or VOM to test your coils to see if they are functioning properly. To access the part, remove the small access panel at the bottom front of the dryer. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also be sure to turn off the gas valve that’s connected to your dryer.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Valve Coil Set• Tools Needed: Multi screwdriver Read More Read Less

This Refrigerator Defrost Thermostat is a safety device that clips onto the evaporator in the freezer. The thermostat turns off the defrost heater in case it gets too warm in ...the freezer section. If your refrigerator does not defrost, replacing the thermostat may alleviate this issue. To access the part, open the freezer door and remove the shelves, mounting brackets (if they release), and the ice bucket. After you remove the back panel, the defrost thermostat is mounted to the end of the evaporator. Replacing the element will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Defrost Thermostat• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Refrigerator Defrost Thermostat is a safety device that clips onto the evaporator inside the freezer. The Defrost Thermostat turns off the defrost heater in case it gets ...too warm in the freezer section. To access the part, you'll have to remove all shelving, bins, rails, and mounting clips from the inside of your freezer so you can access the back panel. Remove the back panel by removing the 6 Phillips screws. Remove the light bulb cover and then lift out the back panel. Replacing the element will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Wire Splicing Tool 8-1/4". This stripper specializes in stripping and cutting wire. This tool is designed with a lean nose for pulling and looping wire and equipped with precision ground cutters.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Defrost Thermostat• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Top Freezer Refrigerator Temperature Control Thermostat sends power to the refrigerant system to keep the unit consistently cooled. If your refrigerator isn't maintaining ...a constant temperature, is becoming too cold or the fan is running continuously, replacing this part may alleviate these issues. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also turn off the refrigerator's water supply before you begin.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Freezer Refrigerator Temperature Control Thermostat• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Cycling Thermostat monitors and regulates the temperature inside the dryer. If your appliance isn't heating as expected, replacing this part may alleviate the issue .... To access the part, you'll need to remove the large back panel of the dryer, then remove the wires and 1/4-inch screw that holds the old thermostat into its housing. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Cycling Thermostat• Tools Needed: Multi screwdriver Read More Read Less

This Gas Range Surface Burner Base distributes the gas through holes or slots to create an even flame across the cooking area. Caution: the wires must be handled with care; en ...sure that they don't fall down inside the appliance after you remove the old burner head. Installing this item will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing this item. Also make sure to turn off the gas valve before the repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Burner Base• Tools Needed: Multi screwdriver Read More Read Less

This Range Sealed Gas Burner Head Assembly directs your oven's gas to the burner head. If the ceramic is cracked on your range or if the burner no longer ignites, replacing th ...is part may alleviate these issues. To install the new part, remove the old burner assembly by turning it counter clockwise by hand. If you are unable to loosen the old burner by hand, using a strap wrench may help. When you remove the ground and the spark wires from the old burner head, make sure they don't fall back into the range top. Turn the new burner head clockwise to lock when replacing. Replacing this part will require no disassembly or repair experience. You must unplug the appliance or shut off the house circuit breaker before installing. Also turn off the gas supply that's connected to your range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Sealed Gas Burner Assembly• No tools required for installation Read More Read Less

This Gas Range Pressure Regulator and Safety Valve controls the gas supply for the bake and broil burners in your oven. Once this valve senses the desired heat, it will open u ...p and allow the gas to travel to the oven burner. If you are no longer getting heat to the burners, you may need to replace the valve. Installing this part will require specialized tools, complicated disassembly of the oven and prior repair experience. We recommend that you hire a qualified technician to install this assembly. If installing yourself, remember to unplug the oven or shut off the house circuit breaker and gas valve for the appliance before beginning.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Pressure Regulator and Safety Valve• Tools Needed: Specialized Tools Read More Read Less