PA Categories

The Gas Dryer Igniter lights the gas in your dryer. If your dryer is no longer supplying heat, this part may be damaged or cracked and may need to be replaced. To access the p ...art, lift the top of the dryer by releasing the spring clips from the top panel with a putty knife. Then remove the door switch wires and the screws that release the front panel. Next, simply loosen the screw that holds in the igniter to remove it. Please note that the bracket is no longer included with this part. If your original igniter was round, also order bracket (item 37001309). Replacing this assembly will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Note that you cannot touch the grey part of the igniter; only handle the igniter by its white plastic covering.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Igniter Kit• Tools Needed: Multi screwdriver, putty knife, 5/16" wrench Read More Read Less

The Refrigerator Water Filter Cap in black is located at the base of the refrigerator. After extracting the water filter, remove the filter cap by turning it counter clockwise .... Install the new cap turning it clockwise and locking it into place. When replaced, purge the air out of the water lines and check that your refrigerator's water dispenses properly. Replacing this part will require no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Water Filter Cap• No tools required for installation Read More Read Less

This Refrigerator FreshFlow™ Air Filter reduces common food odors in the refrigerator and is 15 times more powerful than baking soda. It is recommended that you replace this ... filter every 6 months. Replacing the air filter will require no disassembly or repair experience.Part Specification• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Refrigerator FreshFlow™ Air Filter• No tools required for installation Read More Read Less

This Range Grease Filter traps grease from the exhaust air of your downdraft cooktop and range to prevent it from entering the blower and vent, potentially causing build-up an ...d damage. If your current filter can no longer be cleaned and is not functioning properly, replacing it may alleviate the issue. This part measures 16" L x 9" W. Replacing this part will require basic hand tools, but no disassembly or previous repair experience. Make sure you unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Grease Filter• Tools Needed: Multi screwdriver Read More Read Less

The SxS Refrigerator Water Filter Housing is a grey plastic part that surrounds and protects the appliance’s water filter. To access the part, pull the toe kick free from th ...e front of the appliance. This part has two push-in fittings, one 1/4" fitting and 5/16" one, allowing you to push the plastic tubing water lines directly into the housing for easy installation. Simply push down on the rings near the tubing to release the old lines. Replacing this part will require basic hand tools, some disassembly of the refrigerator and intermediate repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also turn off the refrigerator’s water supply before you begin.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Water Filter Housing• Tools Needed: Multi screwdriver Read More Read Less

The SxS Refrigerator Water Filter Housing is a plastic part that surrounds and protects the appliance’s water filter. This part has two push-in fittings, one 1/4" fitting an ...d 5/16" one, allowing you to push the plastic tubing water lines directly into the housing for easy installation. Simply push down on the rings near the tubing to release the old lines. Replacing this part will require basic hand tools, some disassembly of the refrigerator and intermediate repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also turn off the refrigerator’s water supply before you begin.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Water Filter Housing• Tools Needed: Multi screwdriver Read More Read Less

This Hood Grease Filter traps grease from the exhaust air of your downdraft cooktop to prevent it from entering the blower and vent, potentially causing build-up and damage. I ...f your current filter can no longer be cleaned and is not functioning properly, replacing this part may alleviate the issue. This part measures 12" L x 10" W and is compatible with select KitchenAid brand vent systems. Replacing this part will require basic hand tools, but no disassembly or previous repair experience. Make sure you unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Hood Grease Filter• Tools Needed: Multi screwdriver Read More Read Less

This Microwave Vent Grille, Black, is a plastic replacement piece for your over-the-range microwave that covers components inside the microwave while allowing airflow through ...the slats. Includes mounting clip. This accessory can be used with many different brands and models; check your model number to confirm compatibility. Installing this vent Grille will require basic hand tools and novice repair experience. Be sure to unplug the microwave or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Microwave Vent Grille, Black• Tools Needed: Multi screwdriver Read More Read Less

The Front Load Dryer Lint Screen is a white screen that provides proper air flow and operation of your dryer. After pulling the old filter out, be sure to clean the channels o ...f the lint housing before inserting the new lint screen.The filter should be cleaned before every load of laundry and replaced immediately if damaged. This a replacement lint filter with handle measures approximately 3/8" thick on the left side and 5/8" thick on the right side. Replacing your dryer’s lint filter is a quick and essential way to keep your appliance operating at optimal levels. Installing this part requires no tools, disassembly or repair experience. Recommended Tool: The Cleaning Brush (item 4210463RW) is useful to remove lint and other debris from the dryer’s venting.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Dryer Lint Screen• No tools required for installation Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.