Maytag Appliance Parts

The SxS Refrigerator Air Damper Control Assembly controls the cold airflow from the freezer compartment into the refrigerator compartment. Common reasons for replacing the dam ...per control is if the freezer is the correct temperature but the fridge is too cold or not cold enough. The damper control is located in the freezer inside the ice maker assembly. You will need to remove the ice maker from your refrigerator to access this part. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the refrigerator before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Air Damper Control Assembly• Tools Needed: Multi screwdriver Read More Read Less

The SxS Refrigerator Glass Shelf is a white-edged replacement part for a damaged shelf in your side by side refrigerator. Shelf measures about 18" wide by 18-1/2 " deep and ha ...s a curved front. Replacing this part will require no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Glass Shelf Assembly• No tools required for installation Read More Read Less

This Front Load Washer Door Lock Assembly locks the washer door and tells the control board that the door is closed. If your washer door no longer latches, the wash cycle will ... no longer start, and this part needs to be replaced. When removing the old Door Lock, make note of how the plugs are inserted into the switch. Push the tabs and disconnect the three harness plugs from the old lock. Then you can connect the large plug to the new Door Luck. To connect the remaining two plugs, you'll have to remove the top of the washer to reach them. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Washer Door Lock Assembly• Tools Needed: Multi screwdriver, locking pliers Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The SxS Refrigerator Auger Motor powers the arm inside the ice bucket assembly, allowing ice to flow freely from the dispenser in the front of the appliance. If the auger in y ...our freezer is no longer dispensing the ice properly, replacing this part may alleviate the issue. This part does not include mounting screws. (Screw item WPW10348409). Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) SxS Refrigerator Auger Motor• Tools Needed: Multi screwdriver, socket and needle-nose pliers Read More Read Less

This Range Lower Bake Element provides constant heat from the lower oven during the cooking process. If your oven does not bake properly, replacing this part may alleviate the ... issue. Make sure not to let the wires fall back into the oven wall when disconnecting them from the existing part. This oven bake element features push-on terminal ends. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Lower Bake Element• Tools Needed: Multi screwdriver Read More Read Less

This Dryer Thermal Cut Off Fuse is a safety device designed to protect the dryer from overheating. A multimeter can be used to test the fuse. Always check the dryer venting wh ...en replacing a blown thermal fuse. The thermal cut off is located on top of the burner funnel under the dryer drum, so you'll need to remove the drum from the dryer cabinet to access the old part and replace it. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Thermal Cut Off Fuse• Tools Needed: Multi screwdriver, putty knife, 5/16" nut driver Read More Read Less

This Washer Water Inlet Valve lets the hot and cold water into your washing machine and distributes it around to the dispensers. If you are experiencing a long or slow fill cy ...cle it is often due to a restricted water flow and replacing this part may alleviate the issue. Please note: The valve should never be disassembled and cleaned, only replaced. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn the water supply off to the water and place a towel down when removing the hot and cold fill hoses from the valve. Recommended Item: Consider replacing the hot and cold Fill Hoses (item 8212487RP) at the same time you complete this repair. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Washer Water Inlet Valve• Tools Needed: Multi screwdriver, channel locks and pliers Read More Read Less

WP8317926 Whirlpool Inlet Hose